cfr_sections
Data license: Public Domain (U.S. Government data) · Data source: Federal Register API & Regulations.gov API
12 rows where part_number = 801 and title_number = 7 sorted by section_id
This data as json, CSV (advanced)
Suggested facets: amendment_citations
| section_id ▼ | title_number | title_name | chapter | subchapter | part_number | part_name | subpart | subpart_name | section_number | section_heading | agency | authority | source_citation | amendment_citations | full_text |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 7:7:7.1.2.8.2.0.30.1 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.1 Applicability. | AMS | The requirements set forth in this part 801 describe certain specifications, tolerances, and other technical requirements for official grain inspection equipment and related sample handling systems used in performing inspection services under the Act. | ||||||
| 7:7:7.1.2.8.2.0.30.10 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.10 [Reserved] | AMS | |||||||
| 7:7:7.1.2.8.2.0.30.11 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.11 Related design requirements. | AMS | (a) Suitability. The design, construction, and location of official sampling and inspection equipment and related sample handling systems shall be suitable for the official sampling and inspection activities for which the equipment is to be used. (b) Durability. The design, construction, and material used in official sampling and inspection equipment and related sample handling systems shall assure that, under normal operating conditions, operating parts will remain fully operable, adjustments will remain reasonably constant, and accuracy will be maintained between equipment test periods. (c) Marking and identification. Official sampling and inspection equipment for which tolerances have been established shall be permanently marked to show the manufacturer's name, initials, or trademark; the serial number of the equipment; and the model, the type, and the design or pattern of the equipment. Operational controls for mechanical samplers and related sample handling systems, including but not limited to pushbuttons and switches, shall be conspicuously identified as to the equipment or activity controlled by the pushbutton or switch. (d) Repeatability. Official inspection equipment when tested in accordance with §§ 800.217 and 800.219 shall, within the tolerances prescribed in §§ 801.3 through 801.10, be capable of repeating its results when the equipment is operated in its normal manner. (e) Security. Mechanical samplers and related sample handling systems shall provide a ready means of sealing to deter unauthorized adjustments, removal, or changing of component parts or timing sequence without removing or breaking the seals; and otherwise be designed, constructed, and installed in a manner to prevent deception by any person. (f) Installation requirements. Official sampling and inspection equipment and related sample handling systems shall be installed (1) at a site approved by the Service, (2) according to the manufacturer's instructions, and (3) in such a manner that neither the operation nor the p… | ||||||
| 7:7:7.1.2.8.2.0.30.12 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.12 Design requirements incorporated by reference. | AMS | [57 FR 2673, Jan. 23, 1992, as amended at 69 FR 18803, Apr. 9, 2004] | (a) Moisture meters. All moisture meters approved for use in official grain moisture determination and certification shall meet applicable requirements contained in the FGIS Moisture Handbook and the General Code and Grain Moisture Meters Code of the 1991 edition of the National Institute of Standards and Technology's (NIST) Handbook 44, “Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices.” Pursuant to the provisions of 5 U.S.C. 552(a), the materials in Handbook 44 are incorporated by reference as they exist on the date of approval and a notice of any change in these materials will be published in the Federal Register. The NIST Handbook is for sale by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20403. It is also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. The following Handbook 44 requirements are not incorporated by reference: General Code (1.10.) G-S.5.5. Money Values, Mathematical Agreement G-T.1. Acceptance Tolerances G-UR.3.3. Position of Equipment G-UR.3.4. Responsibility, Money-Operated Devices Grain Moisture Meters (5.56.) N.1.1. Transfer Standards N.1.2. Minimum Test N.1.3. Temperature Measuring Equipment T.2. Tolerance Values T.3. For Test Weight Per Bushel Indications or Recorded Representations UR.3.2. Other Devices not used for Commercial Measurement UR.3.7. Location UR.3.11. Posting of Meter Operating Range General Code (1.10.) Grain Moisture Meters (5.56.) (b) [Reserved] | |||||
| 7:7:7.1.2.8.2.0.30.2 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.2 Meaning of terms. | AMS | (a) Construction. Words used in the singular form in this part shall be considered to imply the plural and vice versa, as appropriate. (b) Definitions. The definitions of terms listed in the part 800 shall have the same meaning when the terms are used in this part 801. For the purposes of this part, the following terms shall have the meanings given for them below. (1) Avoirdupois weight. A unit of weight based on a pound of 16 ounces. (2) Barley pearler. An approved laboratory device used to mechanically dehull kernels of barley or other grain. (3) Deviation from standard. In testing inspection equipment for accuracy, the variation between (i) the individual test result from the equipment that is being tested and (ii) the reference standard or the individual test result from the standard (or National standard) equipment, as applicable. (4) Direct comparison method. An equipment testing procedure wherein transfer standards are tested at the same time and place to compare the performance of two or more units of the same inpsection equipment. One unit of the equipment used in the test shall be standard inspection equipment. (See also sample exchange method). (5) Diverter-type mechanical sampler (primary). An approved device used to obtain representative portions from a flowing stream of grain. (6) Diverter-type mechanical sampler (secondary). An approved device used to subdivide the portions of grain obtained with a diverter-type mechanical sampler (primary). (7) Divider. An approved laboratory device used to mechanically divide a sample of grain into two or more representative portions. (8) Dockage tester. An approved laboratory device used to mechanically separate dockage and/or foreign material from grain. (9) Maintenance tolerance. An allowance established for use in determining whether inspection equipment should be approved for use in performing official inspection services. (10) Mean deviation from standard. In testing inspection equipment for accuracy, the variation between… | ||||||
| 7:7:7.1.2.8.2.0.30.3 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.3 Tolerances for barley pearlers. | AMS | The maintenance tolerances for barley pearlers used in performing official inspection services shall be: | ||||||
| 7:7:7.1.2.8.2.0.30.4 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.4 Tolerances for dockage testers. | AMS | The maintenance tolerances for dockage testers used in performing official inspection services shall be: | ||||||
| 7:7:7.1.2.8.2.0.30.5 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.5 Tolerance for diverter-type mechanical samplers. | AMS | The maintenance tolerance for diverter-type mechanical samplers (primary, or primary and secondary in combination) used in performing official inspection services shall be ±10 percent, mean deviation from standard sampling device using corn or the same type of grain that the system will be used to sample. | ||||||
| 7:7:7.1.2.8.2.0.30.6 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.6 Tolerances for moisture meters. | AMS | [63 FR 34554, June 25, 1998] | (a) The maintenance tolerances for Motomco 919 moisture meters used in performing official inspection services shall be: (1) Headquarters standard meters: (2) All other than Headquarters standard meters: (b) The maintenance tolerances for GAC 2100 moisture meters used in performing official inspection services shall be: (1) Headquarters standard meters. By direct comparison using mid-range Hard Red Winter wheat, ±0.05% mean deviation for the average of the Headquarters standard moisture meters. (2) All other than Headquarters standard meters. By sample exchange using mid-range Hard Red Winter wheat, ±0.15% mean deviation from the standard meter. | |||||
| 7:7:7.1.2.8.2.0.30.7 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.7 Reference methods and tolerances for near-infrared spectroscopy (NIRS) analyzers. | AMS | [63 FR 35505, June 30, 1998, as amended at 69 FR 18803, Apr. 9, 2004; 71 FR 65373, Nov. 8, 2006] | (a) Reference methods. (1) The chemical reference protein determinations used to reference and calibrate official NIRS instruments shall be performed in accordance with “Comparison of Kjeldahl Method for Determination of Crude Protein in Cereal Grains and Oilseeds with Generic Combustion Method: Collaborative Study,” July/August 1993, Ronald Bicsak, Journal of AOAC International Vol. 76, No. 4, 1993, and subsequently approved by the AOAC International as the Combustion method, AOAC International Method 992.23. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Director, Technical Services Division, Federal Grain Inspection Service, 10383 North Executive Hills Blvd., Kansas City, MO 64153-1394. Copies may be inspected at the above address or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (2) The chemical reference starch determination used to reference and calibrate official NIRS instruments shall be performed in accordance with the Corn Refiners Association Method A-20, Analysis for Starch in Corn, Second revision, April 15, 1986, Standard Analytical Methods of the Member Companies of the Corn Refiners Association, Inc. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Director, Technical Services Division, Federal Grain Inspection Service, 10383 North Executive Hills Blvd., Kansas City, MO 64153-1394. Copies may be inspected at the above address or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (b) … | |||||
| 7:7:7.1.2.8.2.0.30.8 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.8 Tolerances for sieves. | AMS | The maintenance tolerances for sieves used in performing official inspection services shall be: (a) Thickness of metal: ±0.0015 inch. (b) Accuracy of perforation: ±0.001 inch from design specification. (c) Sieving accuracy: | ||||||
| 7:7:7.1.2.8.2.0.30.9 | 7 | Agriculture | VIII | A | 801 | PART 801—OFFICIAL PERFORMANCE REQUIREMENTS FOR GRAIN INSPECTION EQUIPMENT | § 801.9 Tolerances for test weight apparatuses. | AMS | The maintenance tolerances for test weight per bushel apparatuses used in performing official inspection services shall be: |
Advanced export
JSON shape: default, array, newline-delimited, object
CREATE TABLE cfr_sections (
section_id TEXT PRIMARY KEY,
title_number INTEGER,
title_name TEXT,
chapter TEXT,
subchapter TEXT,
part_number TEXT,
part_name TEXT,
subpart TEXT,
subpart_name TEXT,
section_number TEXT,
section_heading TEXT,
agency TEXT,
authority TEXT,
source_citation TEXT,
amendment_citations TEXT,
full_text TEXT
);
CREATE INDEX idx_cfr_title ON cfr_sections(title_number);
CREATE INDEX idx_cfr_part ON cfr_sections(part_number);
CREATE INDEX idx_cfr_agency ON cfr_sections(agency);