cfr_sections
Data license: Public Domain (U.S. Government data) · Data source: Federal Register API & Regulations.gov API
97 rows where part_number = 229 and title_number = 49 sorted by section_id
This data as json, CSV (advanced)
Suggested facets: subpart, subpart_name
| section_id ▼ | title_number | title_name | chapter | subchapter | part_number | part_name | subpart | subpart_name | section_number | section_heading | agency | authority | source_citation | amendment_citations | full_text |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 49:49:4.1.1.1.23.1.23.1 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.1 Scope. | FRA | This part prescribes minimum Federal safety standards for all locomotives except those propelled by steam power. | |||||
| 49:49:4.1.1.1.23.1.23.10 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.15 Remote control locomotives. | FRA | [77 FR 21342, Apr. 9, 2012, as amended at 77 FR 75056, Dec. 19, 2012] | (a) Design and operation. (1) Each locomotive equipped with a locomotive control unit (LCU) shall respond only to the operator control units (OCUs) assigned to that receiver. (2) If one or more OCUs are assigned to a LCU, the LCU shall respond only to the OCU that is in primary command. If a subsequent OCU is assigned to a LCU, the previous assignment will be automatically cancelled. (3) If more than one OCU is assigned to a LCU, the secondary OCUs' man down feature, bell, horn, and emergency brake application functions shall remain active. The remote control system shall be designed so that if the signal from the OCU to the RCL is interrupted for a set period not to exceed five seconds, the remote control system shall cause: (i) A full service application of the locomotive and train brakes; and (ii) The elimination of locomotive tractive effort. (4) Each OCU shall be designed to control only one RCL at a time. OCU's having the capability to control more than one RCL shall have a means to lock in one RCL “assignment address” to prevent simultaneous control over more than one locomotive. (5) If an OCU is equipped with an “on” and “off” switch, when the switch is moved from the “on” to the “off” position, the remote control system shall cause: (i) A full service application of the locomotive train brakes; and (ii) The elimination of locomotive tractive effort. (6) Each RCL shall have a distinct and unambiguous audible or visual warning device that indicates to nearby personnel that the locomotive is under active remote control operation. (7) When the main reservoir pressure drops below 90 psi while the RCL is moving, the RCL shall initiate a full service application of the locomotive and train brakes, and eliminate locomotive tractive effort. (8) When the air valves and the electrical selector switch on the RCL are moved from manual to remote control mode or from remote control to manual mode, an emergency application of the locomotive and train brakes shall be initiated. (9) Operating control handles… | ||||
| 49:49:4.1.1.1.23.1.23.11 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.17 Accident reports. | FRA | [79 FR 21636, Apr. 17, 2014] | (a) In the case of an accident due to a failure from any cause of a locomotive or any part or appurtenance of a locomotive, or a person coming in contact with an electrically energized part or appurtenance, that results in serious injury or death of one or more persons, the carrier operating the locomotive shall immediately report the accident by toll free telephone, Area Code 800-424-0201. The report shall state the nature of the accident, number of persons killed or seriously injured, the place at which it occurred, the location at which the locomotive or the affected parts may be inspected by the FRA, and the name, title and phone number of the person making the call. The locomotive or the part or parts affected by the accident shall be preserved intact by the carrier until after the FRA inspection. (b) Written confirmation of the oral report required by paragraph (a) of this section shall be immediately mailed to the Federal Railroad Administration, RRS-25, Washington, D.C. 20590, and contain a detailed description of the accident, including to the extent known, the causes and the number of persons killed and injured. The written report required by this paragraph is in addition to the reporting requirements of 49 CFR part 225. | ||||
| 49:49:4.1.1.1.23.1.23.12 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.19 Prior waivers. | FRA | [77 FR 21343, Apr. 9, 2012] | Waivers from any requirement of this part, issued prior to June 8, 2012, shall terminate on the date specified in the letter granting the waiver. If no date is specified, then the waiver shall automatically terminate on June 8, 2017. | ||||
| 49:49:4.1.1.1.23.1.23.13 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.20 Electronic recordkeeping. | FRA | [77 FR 21343, Apr. 9, 2012, as amended at 77 FR 75056, Dec. 19, 2012] | (a) For purposes of compliance with the recordkeeping requirements of this part, except for the daily inspection record maintained on the locomotive required by § 229.21, the cab copy of Form FRA F 6180-49-A required by § 229.23, the fragmented air brake maintenance record required by § 229.27, and records required under § 229.9, a railroad may create, maintain, and transfer any of the records required by this part through electronic transmission, storage, and retrieval provided that all of the requirements contained in this section are met. (b) Design requirements. Any electronic record system used to create, maintain, or transfer a record required to be maintained by this part shall meet the following design requirements: (1) The electronic record system shall be designed such that the integrity of each record is maintained through appropriate levels of security such as recognition of an electronic signature, or other means, which uniquely identify the initiating person as the author of that record. No two persons shall have the same electronic identity; (2) The electronic system shall ensure that each record cannot be modified, or replaced, once the record is transmitted; (3) Any amendment to a record shall be electronically stored apart from the record which it amends. Each amendment to a record shall uniquely identify the person making the amendment; (4) The electronic system shall provide for the maintenance of inspection records as originally submitted without corruption or loss of data; and (5) Policies and procedures shall be in place to prevent persons from altering electronic records, or otherwise interfering with the electronic system. (c) Operational requirements. Any electronic record system used to create, maintain, or transfer a record required to be maintained by this part shall meet the following operating requirements: (1) The electronic storage of any record required by this part shall be initiated by the person performing the activity to which the record pertains within 24 hours f… | ||||
| 49:49:4.1.1.1.23.1.23.2 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.3 Applicability. | FRA | [54 FR 33229, Aug. 14, 1989, as amended at 64 FR 25659, May 12, 1999; 83 FR 59217, Nov. 21, 2018] | (a) Except as provided in paragraphs (b) through (e) of this section, this part applies to all standard gage railroads. (b) This part does not apply to: (1) A railroad that operates only on track inside an installation which is not part of the general railroad system of transportation; or (2) Rapid transit operations in an urban area that are not connected with the general railroad system of transportation. (c) Paragraphs (a) and (b) of § 229.125 do not apply to Tier II passenger equipment as defined in § 238.5 of this chapter ( i.e., passenger equipment operating at speeds exceeding 125 mph but not exceeding 160 mph). (d) On or after November 8, 1999, paragraphs (a)(1) and (b)(1) of § 229.141 do not apply to “passenger equipment” as defined in § 238.5 of this chapter, unless such equipment is excluded from the requirements of §§ 238.203 through 238.219, and § 238.223 of this chapter by operation of § 238.201(a)(2) of this chapter. (e) Paragraphs (a)(2) through (a)(4), and (b)(2) through (b)(4) of § 229.141 do not apply to “passenger equipment” as defined in § 238.5 of this chapter that is placed in service for the first time on or after September 8, 2000, unless such equipment is excluded from the requirements of §§ 238.203 through 238.219, and § 238.223 of this chapter by operation of § 238.201(a)(2) of this chapter. | ||||
| 49:49:4.1.1.1.23.1.23.3 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.4 Information collection. | FRA | [50 FR 6953, Feb. 19, 1985, as amended at 58 FR 36613, July 8, 1993; 71 FR 63136, Oct. 27, 2006] | (a) The information collection requirements in this part have been reviewed by the Office of Management and Budget pursuant to the Paperwork Reduction Act of 1980, Public Law 96-511, and have been assigned OMB control number 2130-0004. (b) The information collection requirements are found in the following sections: §§ 229.9, 229.17, 229.21, 229.23, 229.25, 229.27, 229.29, 229.31, 229.33, 229.55, 229.103, 229.105, 229.113, 229.121, 229.135, and appendix H to part 229. | ||||
| 49:49:4.1.1.1.23.1.23.4 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.5 Definitions. | FRA | [70 FR 37938, June 30, 2005, as amended at 71 FR 36911, June 28, 2006; 71 FR 47666, Aug. 17, 2006; 71 FR 61857, Oct. 19, 2006; 71 FR 63136, Oct. 27, 2006; 72 FR 59223, Oct. 19, 2007; 77 FR 21342, Apr. 9, 2012; 83 FR 59217, Nov. 21, 2018; 88 FR 70761, Oct. 12, 2023] | As used in this part— AAR means the Association of American Railroads. Acceptable quality level (AQL). The AQL is expressed in terms of percent defective or defects per 100 units. Lots having a quality level equal to a specified AQL will be accepted approximately 95 percent of the time when using the sampling plans prescribed for that AQL. Alerter means a device or system installed in the locomotive cab to promote continuous, active locomotive engineer attentiveness by monitoring select locomotive engineer-induced control activities. If fluctuation of a monitored locomotive engineer-induced control activity is not detected within a predetermined time, a sequence of audible and visual alarms is activated so as to progressively prompt a response by the locomotive engineer. Failure by the locomotive engineer to institute a change of state in a monitored control, or acknowledge the alerter alarm activity through a manual reset provision, results in a penalty brake application that brings the locomotive or train to a stop. Anti-climbers means the parts at the ends of adjoining rail vehicles in a train that are designed to engage when subjected to large buff loads to prevent the override of one vehicle by another. Assignment address means a unique identifier of the RCL that insures that only the OCU's linked to a specific RCL can command that RCL. Associate Administrator for Safety means the Associate Administrator for Safety, Federal Railroad Administration, or that person's delegate as designated in writing. Break means a fracture resulting in complete separation into parts. Build date means the date on which the completed locomotive is shipped by the manufacturer or remanufacturer to the customer, or if the railroad manufactures or remanufactures the locomotive itself, the date on which the locomotive is released from the manufacture or remanufacture facility. Cab means that portion of the superstructure designed to be occupied by the crew operating the locomotive. Carrier means railroad , as th… | ||||
| 49:49:4.1.1.1.23.1.23.5 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.7 Prohibited acts and penalties. | FRA | [77 FR 21342, Apr. 9, 2012, as amended at 77 FR 24421, Apr. 24, 2012; 81 FR 43111, July 1, 2016; 82 FR 16134, Apr. 3, 2017; 83 FR 60748, Nov. 27, 2018; 84 FR 23735, May 23, 2019; 84 FR 37074, July 31, 2019; 86 FR 1758, Jan. 11, 2021; 86 FR 23255, May 3, 2021; 87 FR 15868, Mar. 21, 2022; 88 FR 1128, Jan. 6, 2023; 88 FR 89563, Dec. 28, 2023; 89 FR 106296, Dec. 30, 2024; 90 FR 28165, July 1, 2025] | (a) Federal Rail Safety Laws (49 U.S.C. 20701-20703) make it unlawful for any carrier to use or permit to be used on its line any locomotive unless the entire locomotive and its appurtenances— (1) Are in proper condition and safe to operate in the service to which they are put, without unnecessary peril to life or limb; and (2) Have been inspected and tested as required by this part. (b) Any person (including but not limited to a railroad; any manager, supervisor, official, or other employee or agent of a railroad; any owner, manufacturer, lessor, or lessee of railroad equipment, track, or facilities; any employee of such owner, manufacturer, lessor, lessee, or independent contractor) who violates any requirement of this part or of the Federal Rail Safety Laws or causes the violation of any such requirement is subject to a civil penalty of at least the minimum civil monetary penalty and not more than the ordinary maximum civil monetary penalty per violation. However, penalties may be assessed against individuals only for willful violations, and a penalty not to exceed the aggravated maximum civil monetary penalty per violation may be assessed, where: A grossly negligent violation, or a pattern of repeated violations, has created an imminent hazard of death or injury to persons; or a death or injury has occurred. See 49 CFR part 209, appendix A. Each day a violation continues shall constitute a separate offense. FRA's website at https://railroads.dot.gov/ contains a statement of agency civil penalty policy. (c) Any person who knowingly and willfully falsifies a record or report required by this part is subject to criminal penalties under 49 U.S.C. 21311. | ||||
| 49:49:4.1.1.1.23.1.23.6 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.9 Movement of non-complying locomotives. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 61 FR 8887, Mar. 6, 1996; 67 FR 16050, Apr. 4, 2002; 72 FR 59223, Oct. 19, 2007] | (a) Except as provided in paragraphs (b), (c), § 229.125(g), and § 229.131(b) and (c)(1), a locomotive with one or more conditions not in compliance with this part may be moved only as a lite locomotive or a dead locomotive after the carrier has complied with the following: (1) A qualified person shall determine— (i) That it is safe to move the locomotive; and (ii) The maximum speed and other restrictions necessary for safely conducting the movement; (2)(i) The engineer in charge of the movement of the locomotive shall be notified in writing and inform all other crew members in the cab of the presence of the non-complying locomotive and the maximum speed and other restrictions determined under paragraph (a)(1)(ii) of this section. (ii) A copy of the tag described in paragraph (a)(3) of this section may be used to provide the notification required by paragraph (a)(2)(i) of this section. (3) A tag bearing the words “non-complying locomotive” and containing the following information, shall be securely attached to the control stand on each MU or control cab locomotive and to the isolation switch or near the engine start switch on every other type of locomotive— (i) The locomotive number; (ii) The name of the inspecting carrier; (iii) The inspection location and date; (iv) The nature of each defect; (v) Movement restrictions, if any; (vi) The destination; and (vii) The signature of the person making the determinations required by this paragraph. (b) A locomotive that develops a non-complying condition enroute may continue to utilize its propelling motors, if the requirements of paragraph (a) are otherwise fully met, until the earlier of— (1) The next calendar day inspection, or (2) The nearest forward point where the repairs necessary to bring it into compliance can be made. (c) A non-complying locomotive may be moved lite or dead within a yard, at speeds not in excess of 10 miles per hour, without meeting the requirements of paragraph (a) of this section if the movement is solely for the purpose of r… | ||||
| 49:49:4.1.1.1.23.1.23.7 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.11 Locomotive identification. | FRA | (a) The letter “F” shall be legibly shown on each side of every locomotive near the end which for identification purposes will be known as the front end. (b) The locomotive number shall be displayed in clearly legible numbers on each side of each locomotive. | |||||
| 49:49:4.1.1.1.23.1.23.8 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.13 Control of locomotives. | FRA | Except when a locomotive is moved in accordance with § 229.9, whenever two or more locomotives are coupled in remote or multiple control, the propulsion system, the sanders, and the power brake system of each locomotive shall respond to control from the cab of the controlling locomotive. If a dynamic brake or regenerative brake system is in use, that portion of the system in use shall respond to control from the cab of the controlling locomotive. | |||||
| 49:49:4.1.1.1.23.1.23.9 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | A | Subpart A—General | § 229.14 Non-MU control cab locomotives. | FRA | On each non-MU control cab locomotive, only those components added to the passenger car that enable it to serve as a lead locomotive, control the locomotive actually providing tractive power, and otherwise control the movement of the train, are subject to this part. | |||||
| 49:49:4.1.1.1.23.2.23.1 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.21 Daily inspection. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 50 FR 6953, Feb. 19, 1985; 67 FR 16050, Apr. 4, 2002; 88 FR 70761, Oct. 12, 2023] | (a) Except for MU locomotives, each locomotive in use shall be inspected at least once during each calendar day. A written report of the inspection shall be made. This report shall contain the name of the carrier; the initials and number of the locomotive; the place, date and time of the inspection; a description of the non-complying conditions disclosed by the inspection; and the signature of the employee making the inspection. Except as provided in §§ 229.9, 229.136, 229.137, and 229.139, any conditions that constitute non-compliance with any requirement of this part shall be repaired before the locomotive is used. Except with respect to conditions that do not comply with §§ 229.136, 229.137, or 229.139, a notation shall be made on the report indicating the nature of the repairs that have been made. Repairs made for conditions that do not comply with §§ 229.136, 229.137, or 229.139 may be noted on the report, or in electronic form. The person making the repairs shall sign the report. The report shall be filed and retained for at least 92 days in the office of the carrier at the terminal at which the locomotive is cared for. A record shall be maintained on each locomotive showing the place, date and time of the previous inspection. (b) Each MU locomotive in use shall be inspected at least once during each calendar day and a written report of the inspection shall be made. This report may be part of a single master report covering an entire group of MU locomotives. If any non-complying conditions are found, a separate, individual report shall be made containing the name of the carrier; the initials and number of the locomotive; the place, date, and time of the inspection; the non-complying conditions found; and the signature of the inspector. Except as provided in §§ 229.9, 229.136, 229.137, and 229.139, any conditions that constitute non-compliance with any requirement of this part shall be repaired before the locomotive is used. Except with respect to conditions that do not comply with §§ 229.136, 229.137, or 2… | ||||
| 49:49:4.1.1.1.23.2.23.2 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.22 Passenger locomotive inspection and repair record. | FRA | [88 FR 70761, Oct. 12, 2023] | (a) Application. This section applies only to lead locomotives of trains used in commuter or intercity passenger service, i.e., locomotives subject to the requirements of § 229.136. (b) Dates. (1) Each locomotive subject to the requirements of § 229.136 shall use and maintain Form FRA F 6180-49AP in accordance with the requirements of § 229.136, except that Form FRA F 6180-49A may fulfill any requirement in § 229.136 with respect to Form FRA F 6180-49AP until October 12, 2027. (2) For purposes of complying with the inspection, testing, and repair recordkeeping requirements in §§ 229.23, 229.27, 229.29, 229.31, 229.33, 229.55, 229.103, 229.105, 229.114, 229.123, and 229.135 with respect to Form FRA F 6180-49A, each locomotive subject to the requirements of § 229.136 shall instead use and maintain Form FRA F 6180-49AP no later than October 12, 2027. (c) Earlier adoption. Railroads may adopt use of Form FRA F 6180-49AP earlier than required for locomotives subject to the requirements of § 229.136. (d) Effect. Nothing in this section affects the requirements in this part for use of Form FRA F 6180-49A for locomotives not subject to the requirements of § 229.136. | ||||
| 49:49:4.1.1.1.23.2.23.3 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.23 Periodic inspection: general. | FRA | [77 FR 21344, Apr. 9, 2012, as amended at 77 FR 75056, Dec. 19, 2012] | (a) Each locomotive shall be inspected at each periodic inspection to determine whether it complies with this part. Except as provided in § 229.9, all non-complying conditions shall be repaired before the locomotive is used. Except as provided in § 229.33 and paragraph (b) of this section, the interval between any two periodic inspections may not exceed 92 days. Periodic inspections shall only be made where adequate facilities are available. At each periodic inspection, a locomotive shall be positioned so that a person may safely inspect the entire underneath portion of the locomotive. (b) For each locomotive equipped with advanced microprocessor-based on-board electronic condition monitoring controls: (1) The interval between periodic inspections shall not exceed 184 days; and (2) At least once each 33 days, the daily inspection required by § 229.21, shall be performed by a qualified mechanical inspector as defined by § 229.5. A record of the inspection that contains the name of the person performing the inspection and the date that it was performed shall be maintained in the locomotive cab until the next periodic inspection is performed. (c) Each new locomotive shall receive an initial periodic inspection before it is used. (d) At the initial periodic inspection, the date and place of the last tests performed that are the equivalent of the tests required by §§ 229.27, 229.29, and 229.31 shall be entered on Form FRA F 6180-49A. These dates shall determine when the tests first become due under §§ 229.27, 229.29, and 229.31. Out of use credit may be carried over from Form FRA F 6180-49 and entered on Form FRA F 6180-49A. (e) Each periodic inspection shall be recorded on Form FRA F 6180-49A. The form shall be signed by the person conducting the inspection and certified by that person's supervisor that the work was done. The form shall be displayed under a transparent cover in a conspicuous place in the cab of each locomotive. A railroad maintaining and transferring records as provided for in § 229.20 shall pr… | ||||
| 49:49:4.1.1.1.23.2.23.4 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.25 Tests: Every periodic inspection. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 58 FR 36614, July 8, 1993; 60 FR 27905, May 26, 1995; 66 FR 4192, Jan. 17, 2001; 70 FR 37939, June 30, 2005; 77 FR 21344, Apr. 9, 2012] | Each periodic inspection shall include the following: (a) All mechanical gauges used by the engineer to aid in the control or braking of the train or locomotive, except load meters used in conjunction with an auxiliary brake system, shall be tested by comparison with a dead-weight tester or a test gauge designed for this purpose. (b) All electrical devices and visible insulation shall be inspected. (c) All cable connections between locomotives and jumpers that are designed to carry 600 volts or more shall be thoroughly cleaned, inspected, and tested for continuity. (d) Event recorder. A microprocessor-based self-monitoring event recorder, if installed, is exempt from periodic inspection under paragraphs (d)(1) through (5) of this section and shall be inspected annually as required by § 229.27(c). Other types of event recorders, if installed, shall be inspected, maintained, and tested in accordance with instructions of the manufacturer, supplier, or owner thereof and in accordance with the following criteria: (1) A written or electronic copy of the instructions in use shall be kept at the point where the work is performed and a hard-copy version, written in the English language, shall be made available upon request to FRA. (2) The event recorder shall be tested before any maintenance work is performed on it. At a minimum, the event recorder test shall include cycling, as practicable, all required recording elements and determining the full range of each element by reading out recorded data. (3) If the pre-maintenance test reveals that the device is not recording all the specified data and that all recordings are within the designed recording elements, this fact shall be noted, and maintenance and testing shall be performed as necessary until a subsequent test is successful. (4) When a successful test is accomplished, a copy of the data-verification results shall be maintained in any medium with the maintenance records for the locomotive until the next one is filed. (5) A railroad's event recorder period… | ||||
| 49:49:4.1.1.1.23.2.23.5 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.27 Annual tests. | FRA | [77 FR 21345, Apr. 9, 2012] | (a) All testing under this section shall be performed at intervals that do not exceed 368 calendar days. (b) Load meters that indicate current (amperage) being applied to traction motors shall be tested. Each device used by the engineer to aid in the control or braking of the train or locomotive that provides an indication of air pressure electronically shall be tested by comparison with a test gauge or self-test designed for this purpose. An error greater than five percent or greater than three pounds per square inch shall be corrected. The date and place of the test shall be recorded on Form FRA F 6180-49A, and the person conducting the test and that person's supervisor shall sign the form. (c) A microprocessor-based event recorder with a self-monitoring feature equipped to verify that all data elements required by this part are recorded, requires further maintenance and testing only if either of the following conditions exist: (1) The self-monitoring feature displays an indication of a failure. If a failure is displayed, further maintenance and testing must be performed until a subsequent test is successful. When a successful test is accomplished, a record, in any medium, shall be made of that fact and of any maintenance work necessary to achieve the successful result. This record shall be available at the location where the locomotive is maintained until a record of a subsequent successful test is filed; or, (2) A download of the event recorder, taken within the preceding 30 days and reviewed for the previous 48 hours of locomotive operation, reveals a failure to record a regularly recurring data element or reveals that any required data element is not representative of the actual operations of the locomotive during this time period. If the review is not successful, further maintenance and testing shall be performed until a subsequent test is successful. When a successful test is accomplished, a record, in any medium, shall be made of that fact and of any maintenance work necessary to achieve the successf… | ||||
| 49:49:4.1.1.1.23.2.23.6 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.29 Air brake system calibration, maintenance, and testing. | FRA | [77 FR 21345, Apr. 9, 2012, as amended at 77 FR 75057, Dec. 19, 2012] | (a) A locomotive's air brake system shall receive the calibration, maintenance, and testing as prescribed in this section. The level of maintenance and testing and the intervals for receiving such maintenance and testing of locomotives with various types of air brake systems shall be conducted in accordance with paragraphs (d) through (f) of this section. Records of the maintenance and testing required in this section shall be maintained in accordance with paragraph (g) of this section. (b) Except for DMU or MU locomotives covered under § 238.309 of this chapter, the air flow method (AFM) indicator shall be calibrated in accordance with § 232.205(c)(1)(iii) at intervals not to exceed 92 days, and records shall be maintained as prescribed paragraph (g)(1) of this section. (c) Except for DMU or MU locomotives covered under § 238.309 of this chapter, the extent of air brake system maintenance and testing that is required on a locomotive shall be in accordance with the following levels: (1) Level one: Locomotives shall have the filtering devices or dirt collectors located in the main reservoir supply line to the air brake system cleaned, repaired, or replaced. (2) Level two: Locomotives shall have the following components cleaned, repaired, and tested: brake cylinder relay valve portions; main reservoir safety valves; brake pipe vent valve portions; and, feed and reducing valve portions in the air brake system (including related dirt collectors and filters). (3) Level three: Locomotives shall have the components identified in this paragraph removed from the locomotive and disassembled, cleaned and lubricated (if necessary), and tested. In addition, all parts of such components that can deteriorate within the inspection interval as defined in paragraphs (d) through (f) of this section shall be replaced and tested. The components include: all pneumatic components of the locomotive equipment's brake system that contain moving parts, and are sealed against air leaks; all valves and valve portions; electric-pne… | ||||
| 49:49:4.1.1.1.23.2.23.7 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.31 Main reservoir tests. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 71 FR 61857, Oct. 19, 2006] | (a) Before it is placed in service, each main reservoir other than an aluminum reservoir shall be subjected to a pneumatic or hydrostatic pressure of at least 25 percent more than the maximum working pressure fixed by the chief mechanical officer. The test date, place, and pressure shall be recorded on Form FRA F 6180-49A, block eighteen. Except as provided in paragraph (c) of this section, at intervals that do not exceed 736 calendar days, each main reservoir other than an aluminum reservoir shall be subjected to a hydrostatic pressure of at least 25 percent more than the maximum working pressure fixed by the chief mechanical officer. The test date, place, and pressure shall be recorded on Form FRA F 6180-49A, and the person performing the test and that person's supervisor shall sign the form. (b) Except as provided in paragraph (c) of this section, each main reservoir other than an aluminum reservoir shall be hammer tested over its entire surface while the reservoir is empty at intervals that do not exceed 736 calendar days. The test date and place shall be recorded on Form FRA F 6180-49A, and the person performing the test and that person's supervisor shall sign the form. (c) Each welded main reservoir originally constructed to withstand at least five times the maximum working pressure fixed by the chief mechanical officer may be drilled over its entire surface with telltale holes that are three-sixteenths of an inch in diameter. The holes shall be spaced not more than 12 inches apart, measured both longitudinally and circumferentially, and drilled from the outer surface to an extreme depth determined by the formula— D = (.6PR/S-0.6P) Where: D = extreme depth of telltale holes in inches but in no case less than one-sixteenth inch; P = certified working pressure in pounds per square inch; S = one-fifth of the minimum specified tensile strength of the material in pounds per square inch; and R = inside radius of the reservoir in inches. Where: D = extreme depth of telltale holes in inches but… | ||||
| 49:49:4.1.1.1.23.2.23.8 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | B | Subpart B—Inspections and Tests | § 229.33 Out-of-use credit. | FRA | When a locomotive is out of use for 30 or more consecutive days or is out of use when it is due for any test or inspection required by § 229.23, § 229.25, § 229.27, § 229.29, or § 229.31, an out-of-use notation showing the number of out-of-use days shall be made on an inspection line on Form FRA F 6180-49A. A supervisory employee of the carrier who is responsible for the locomotive shall attest to the notation. If the locomotive is out of use for one or more periods of at least 30 consecutive days each, the interval prescribed for any test or inspection under this part may be extended by the number of days in each period the locomotive is out of use since the last test or inspection in question. A movement made in accordance with § 229.9 is not a use for purposes of determining the period of the out-of-use credit. | |||||
| 49:49:4.1.1.1.23.3.23.1 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.41 Protection against personal injury. | FRA | Fan openings, exposed gears and pinions, exposed moving parts of mechanisms, pipes carrying hot gases and high-voltage equipment, switches, circuit breakers, contactors, relays, grid resistors, and fuses shall be in non-hazardous locations or equipped with guards to prevent personal injury. | |||||
| 49:49:4.1.1.1.23.3.23.2 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.43 Exhaust and battery gases. | FRA | (a) Products of combustion shall be released entirely outside the cab and other compartments. Exhaust stacks shall be of sufficient height or other means provided to prevent entry of products of combustion into the cab or other compartments under usual operating conditions. (b) Battery containers shall be vented and batteries kept from gassing excessively. | |||||
| 49:49:4.1.1.1.23.3.23.3 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.45 General condition. | FRA | All systems and components on a locomotive shall be free of conditions that endanger the safety of the crew, locomotive or train. These conditions include: insecure attachment of components, including third rail shoes or beams, traction motors and motor gear cases, and fuel tanks; fuel, oil, water, steam, and other leaks and accumulations of oil on electrical equipment that create a personal injury hazard; improper functioning of components, including slack adjusters, pantograph operating cylinders, circuit breakers, contactors, relays, switches, and fuses; and cracks, breaks, excessive wear and other structural infirmities of components, including quill drives, axles, gears, pinions, pantograph shoes and horns, third rail beams, traction motor gear cases, and fuel tanks. | |||||
| 49:49:4.1.1.1.23.3.24.10 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.57 Foundation brake gear. | FRA | A lever, rod, brake beam, hanger, or pin may not be worn through more than 30 percent of its cross-sectional area, cracked, broken, or missing. All pins shall be secured in place with cotters, split keys, or nuts. Brake shoes shall be fastened with a brake shoe key and aligned in relation to the wheel to prevent localized thermal stress in the edge of the rim or the flange. | |||||
| 49:49:4.1.1.1.23.3.24.11 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.59 Leakage. | FRA | (a) Leakage from the main air reservoir and related piping may not exceed an average of 3 pounds per square inch per minute for 3 minutes after the pressure has been reduced to 60 percent of the maximum pressure. (b) Brake pipe leakage may not exceed 5 pounds per square inch per minute. (c) With a full service application at maximum brake pipe pressure and with communication to the brake cylinders closed, the brakes shall remain applied at least 5 minutes. (d) Leakage from control air reservoir, related piping, and pneumatically operated controls may not exceed an average of 3 pounds per square inch per minute for 3 minutes. | |||||
| 49:49:4.1.1.1.23.3.24.4 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.46 Brakes: general. | FRA | [77 FR 21346, Apr. 9, 2012] | (a) Before each trip, the railroad shall know the following: (1) The locomotive brakes and devices for regulating pressures, including but not limited to the automatic and independent brake control systems, operate as intended; and (2) The water and oil have been drained from the air brake system of all locomotives in the consist. (b) A locomotive with an inoperative or ineffective automatic or independent brake control system will be considered to be operating as intended for purposes of paragraph (a) of this section, if all of the following conditions are met: (1) The locomotive is in a trailing position and is not the controlling locomotive in a distributed power train consist; (2) The railroad has previously determined, in conjunction with the locomotive and/or airbrake manufacturer, that placing such a locomotive in trailing position adequately isolates the non-functional valves so as to allow safe operation of the brake systems from the controlling locomotive; (3) If deactivation of the circuit breaker for the air brake system is required, it shall be specified in the railroad's operating rules; (4) A tag shall immediately be placed on the isolation switch of the locomotive giving the date and location and stating that the unit may only be used in a trailing position and may not be used as a lead or controlling locomotive; (5) The tag required in paragraph (b)(4) of this section remains attached to the isolation switch of the locomotive until repairs are made; and (6) The inoperative or ineffective brake control system is repaired prior to or at the next periodic inspection. | ||||
| 49:49:4.1.1.1.23.3.24.5 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.47 Emergency brake valve. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 71 FR 61857, Oct. 19, 2006] | (a) Except for locomotives with cabs designed for occupancy by only one person, each road locomotive shall be equipped with a brake pipe valve that is accessible to a member of the crew, other than the engineer, from that crew member's position in the cab. On car body type locomotives, a brake pipe valve shall be attached to the wall adjacent to each end exit door. The words “Emergency Brake Valve” shall be legibly stenciled or marked near each brake pipe valve or shall be shown on an adjacent badge plate. (b) DMU, MU, and control cab locomotives operated in road service shall be equipped with an emergency brake valve that is accessible to another crew member in the passenger compartment or vestibule. The words “Emergency Brake Valve” shall be legibly stenciled or marked near each valve or shall be shown on an adjacent badge plate. | ||||
| 49:49:4.1.1.1.23.3.24.6 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.49 Main reservoir system. | FRA | (a)(1) The main reservoir system of each locomotive shall be equipped with at least one safety valve that shall prevent an accumulation of pressure of more than 15 pounds per square inch above the maximum working air pressure fixed by the chief mechanical officer of the carrier operating the locomotive. (2) Except for non-equipped MU locomotives built prior to January 1, 1981, each locomotive that has a pneumatically actuated system of power controls shall be equipped with a separate reservoir of air under pressure to be used for operating those power controls. The reservoir shall be provided with means to automatically prevent the loss of pressure in the event of a failure of main air pressure, have storage capacity for not less than three complete operating cycles of control equipment and be located where it is not exposed to damage. (b) A governor shall be provided that stops and starts or unloads and loads the air compressor within 5 pounds per square inch above or below the maximum working air pressure fixed by the carrier. (c) Each compressor governor used in connection with the automatic air brake system shall be adjusted so that the compressor will start when the main reservoir pressure is not less than 15 pounds per square inch above the maximum brake pipe pressure fixed by the carrier and will not stop the compressor until the reservoir pressure has increased at least 10 pounds. | |||||
| 49:49:4.1.1.1.23.3.24.7 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.51 Aluminum main reservoirs. | FRA | (a) Aluminum main reservoirs used on locomotives shall be designed and fabricated as follows: (1) The heads and shell shall be made of Aluminum Association Alloy No. 5083-0, produced in accordance with American Society of Mechnical Engineers (ASME) Specification SB-209, as defined in the “ASME Boiler and Pressure Vessel Code” (1971 edition), section II, Part B, page 123, with a minimum tensile strength of 40,000 p.s.i. (40 k.s.i.). (2) Each aluminum main reservoir shall be designed and fabricated in accordance with the “ASME Boiler and Pressure Vessel Code,” section VIII, Division I (1971 edition), except as otherwise provided in this part. (3) An aluminum main reservoir shall be constructed to withstand at least five times its maximum working pressure or 800 p.s.i., whichever is greater. (4) Each aluminum main reservoir shall have at least two inspection openings to permit complete circumferential visual observation of the interior surface. On reservoirs less than 18 inches in diameter, the size of each inspection opening shall be at least that of 1 1/2 -inch threaded iron pipe, and on reservoirs 18 or more inches in diameter, the size of each opening shall be at least that of 2-inch threaded iron pipe. (b) The following publications, which contain the industry standards incorporated by reference in paragraph (a) of this section, may be obtained from the publishers and are also on file in the Office of Safety of the Federal Railroad Administration, Washington, DC 20590. Sections II and VIII of the “ASME Boiler and Pressure Vessel Code” (1971 edition) are published by the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, New York 10017. | |||||
| 49:49:4.1.1.1.23.3.24.8 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.53 Brake gauges. | FRA | [66 FR 4192, Jan. 17, 2001] | All mechanical gauges and all devices providing indication of air pressure electronically that are used by the engineer to aid in the control or braking of the train or locomotive shall be located so that they may be conveniently read from the engineer's usual position during operation of the locomotive. A gauge or device shall not be more than five percent or three pounds per square inch in error, whichever is less. | ||||
| 49:49:4.1.1.1.23.3.24.9 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.55 Piston travel. | FRA | (a) Brake cylinder piston travel shall be sufficient to provide brake shoe clearance when the brakes are released. (b) When the brakes are applied on a standing locomotive, the brake cylinder piston travel may not exceed 1 1/2 inches less than the total possible piston travel. The total possible piston travel for each locomotive shall be entered on Form FRA F 6180-49A. (c) The minimum brake cylinder pressure shall be 30 pounds per square inch. | |||||
| 49:49:4.1.1.1.23.3.25.12 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.61 Draft system. | FRA | [77 FR 21346, Apr. 9, 2012] | (a) A coupler may not have any of the following conditions: (1) A distance between the guard arm and the knuckle nose of more than 5 5/16 inches on D&E couplers. (2) A crack or break in the side wall or pin bearing bosses outside of the shaded areas shown in Figure 1 or in the pulling face of the knuckle. (3) A coupler assembly without anti-creep protection. (4) Free slack in the coupler or drawbar not absorbed by friction devices or draft gears that exceeds one-half inches. (5) A broken or cracked coupler carrier. (6) A broken or cracked yoke. (7) A broken draft gear. (b) A device shall be provided under the lower end of all drawbar pins and articulated connection pins to prevent the pin from falling out of place in case of breakage. | ||||
| 49:49:4.1.1.1.23.3.26.13 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.63 Lateral motion. | FRA | (a) Except as provided in paragraph (b), the total uncontrolled lateral motion between the hubs of the wheels and boxes, between boxes and pedestals or both, on any pair of wheels may not exceed 1 inch on non-powered axles and friction bearing powered axles, or 3/4 inch on all other powered axles. (b) The total uncontrolled lateral motion may not exceed 1 1/4 inches on the center axle of three-axle trucks. | |||||
| 49:49:4.1.1.1.23.3.26.14 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.64 Plain bearings. | FRA | A plain bearing box shall contain visible free oil and may not be cracked to the extent that it will leak oil. | |||||
| 49:49:4.1.1.1.23.3.26.15 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.65 Spring rigging. | FRA | (a) Protective construction or safety hangers shall be provided to prevent spring planks, spring seats or bolsters from dropping to track structure in event of a hanger or spring failure. (b) An elliptical spring may not have its top (long) leaf broken or any other three leaves broken, except when that spring is part of a nest of three or more springs and none of the other springs in the nest has its top leaf or any other three leaves broken. An outer coil spring or saddle may not be broken. An equalizer, hanger, bolt, gib, or pin may not be cracked or broken. A coil spring may not be fully compressed when the locomotive is at rest. (c) A shock absorber may not be broken or leaking clearly formed droplets of oil or other fluid. | |||||
| 49:49:4.1.1.1.23.3.26.16 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.67 Trucks. | FRA | (a) The male center plate shall extend into the female center plate at least 3/4 inch. On trucks constructed to transmit tractive effort through the center plate or center pin, the male center plate shall extend into the female center plate at least 1 1/2 inches. Maximum lost motion in a center plate assemblage may not exceed 1/2 inch. (b) Each locomotive shall have a device or securing arrangement to prevent the truck and locomotive body from separating in case of derailment. (c) A truck may not have a loose tie bar or a cracked or broken center casting, motor suspension lug, equalizer, hanger, gib or pin. A truck frame may not be broken or have a crack in a stress area that may affect its structural integrity. | |||||
| 49:49:4.1.1.1.23.3.26.17 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.69 Side bearings. | FRA | (a) Friction side bearings with springs designed to carry weight may not have more than 25 percent of the springs in any one nest broken. (b) Friction side bearings may not be run in contact unless designed to carry weight. Maximum clearance of side bearings may not exceed one-fourth inch on each side or a total of one-half inch on both sides, except where more than two side bearings are used under the same rigid superstructure. The clearance on one pair of side bearings under the same rigid superstructure shall not exceed one-fourth inch on each side or a total of one-half inch on both sides; the other side bearings under the same rigid superstructure may have one-half inch clearance on each side or a total of 1 inch on both sides. These clearances apply where the spread of the side bearings is 50 inches or less; where the spread is greater, the side bearing clearance may only be increased proportionately. | |||||
| 49:49:4.1.1.1.23.3.26.18 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.71 Clearance above top of rail. | FRA | No part or appliance of a locomotive except the wheels, flexible nonmetallic sand pipe extension tips, and trip cock arms may be less than 2 1/2 inches above the top of rail. | |||||
| 49:49:4.1.1.1.23.3.26.19 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.73 Wheel sets. | FRA | (a) The variation in the circumference of wheels on the same axle may not exceed 1/4 inch (two tape sizes) when applied or turned. (b) The maximum variation in the diameter between any two wheel sets in a three-powered-axle truck may not exceed 3/4 inch, except that when shims are used at the journal box springs to compensate for wheel diameter variation, the maximum variation may not exceed 1 1/4 inch. The maximum variation in the diameter between any two wheel sets on different trucks on a locomotive that has three-powered-axle trucks may not exceed 1 1/4 inch. The diameter of a wheel set is the average diameter of the two wheels on an axle. (c) On standard gauge locomotives, the distance between the inside gauge of the flanges on non-wide flange wheels may not be less than 53 inches or more than 53 1/2 inches. The distance between the inside gauge of the flanges on wide flange wheels may not be less than 53 inches or more than 53 1/4 inches. (d) The distance back to back of flanges of wheels mounted on the same axle shall not vary more than 1/4 inch. | |||||
| 49:49:4.1.1.1.23.3.26.20 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.75 Wheels and tire defects. | FRA | Wheels and tires may not have any of the following conditions: (a) A single flat spot that is 2 1/2 inches or more in length, or two adjoining spots that are each two or more inches in length. (b) A gouge or chip in the flange that is more than 1 1/2 inches in length and 1/2 inch in width. (c) A broken rim, if the tread, measured from the flange at a point five-eighths inch above the tread, is less than 3 3/4 inches in width. (d) A shelled-out spot 2 1/2 inches or more in length, or two adjoining spots that are each two or more inches in length. (e) A seam running lengthwise that is within 3 3/4 inches of the flange. (f) A flange worn to a 7/8 inch thickness or less, gauged at a point 3/8 inch above the tread. (g) A tread worn hollow 5/16 inch or more on a locomotive in road service or 3/8 inch or more on a locomotive in switching service. (h) A flange height of 1 1/2 inches or more measured from tread to the top of the flange. (i) Tires less than 1 1/2 inches thick. (j) Rims less than 1 inch thick on a locomotive in road service or less than 3/4 inch on a locomotive in yard service. (k) A crack or break in the flange, tread, rim, plate, or hub. (l) A loose wheel or tire. (m) Fusion welding may not be used on tires or steel wheels of locomotives, except for the repair of flat spots and worn flanges on locomotives used exclusively in yard service. A wheel that has been welded is a welded wheel for the life of the wheel. | |||||
| 49:49:4.1.1.1.23.3.27.21 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.77 Current collectors. | FRA | (a) Pantographs shall be so arranged that they can be operated from the engineer's normal position in the cab. Pantographs that automatically rise when released shall have an automatic locking device to secure them in the down position. (b) Each pantograph operating on an overhead trolley wire shall have a device for locking and grounding it in the lowest position, that can be applied and released only from a position where the operator has a clear view of the pantograph and roof without mounting the roof. | |||||
| 49:49:4.1.1.1.23.3.27.22 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.79 Third rail shoes. | FRA | When locomotives are equipped with both third rail and overhead collectors, third-rail shoes shall be deenergized while in yards and at stations when current collection is exclusively from the overhead conductor. | |||||
| 49:49:4.1.1.1.23.3.27.23 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.81 Emergency pole; shoe insulation. | FRA | (a) Each locomotive equipped with a pantograph operating on an overhead trolley wire shall have an emergency pole suitable for operating the pantograph. Unless the entire pole can be safely handled, the part of the pole which can be safely handled shall be marked to so indicate. This pole shall be protected from moisture when not in use. (b) Each locomotive equipped with third-rail shoes shall have a device for insulating the current collecting apparatus from the third rail. | |||||
| 49:49:4.1.1.1.23.3.27.24 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.83 Insulation or grounding of metal parts. | FRA | All unguarded noncurrent-carrying metal parts subject to becoming charged shall be grounded or thoroughly insulated. | |||||
| 49:49:4.1.1.1.23.3.27.25 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.85 High voltage markings: doors, cover plates, or barriers. | FRA | [77 FR 21346, Apr. 9, 2012] | All doors, cover plates, or barriers providing direct access to high voltage equipment shall be marked “Danger-High Voltage” or with the word “Danger” and the normal voltage carried by the parts so protected. | ||||
| 49:49:4.1.1.1.23.3.27.26 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.87 Hand-operated switches. | FRA | All hand-operated switches carrying currents with a potential of more than 150 volts that may be operated while under load shall be covered and shall be operative from the outside of the cover. Means shall be provided to show whether the switches are open or closed. Switches that should not be operated while under load shall be legibly marked with the words “must not be operated under load” and the voltage carried. | |||||
| 49:49:4.1.1.1.23.3.27.27 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.89 Jumpers; cable connections. | FRA | (a) Jumpers and cable connections between locomotives shall be so located and guarded to provide sufficient vertical clearance. They may not hang with one end free. (b) Cable and jumper connections between locomotive may not have any of the following conditions: (1) Broken or badly chafed insulation. (2) Broken plugs, receptacles or terminals. (3) Broken or protruding strands of wire. | |||||
| 49:49:4.1.1.1.23.3.27.28 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.91 Motors and generators. | FRA | A motor or a generator may not have any of the following conditions: (a) Be shorted or grounded. (b) Throw solder excessively. (c) Show evidence of coming apart. (d) Have an overheated support bearing. (e) Have an excessive accumulation of oil. | |||||
| 49:49:4.1.1.1.23.3.28.29 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.93 Safety cut-off device. | FRA | The fuel line shall have a safety cut-off device that— (a) Is located adjacent to the fuel supply tank or in another safe location; (b) Closes automatically when tripped and can be reset without hazard; and (c) Can be hand operated from clearly marked locations, one inside the cab and one on each exterior side of the locomotive. | |||||
| 49:49:4.1.1.1.23.3.28.30 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.95 Venting. | FRA | Fuel tank vent pipes may not discharge on the roof nor on or between the rails. | |||||
| 49:49:4.1.1.1.23.3.28.31 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.97 Grounding fuel tanks. | FRA | Fuel tanks and related piping shall be electrically grounded. | |||||
| 49:49:4.1.1.1.23.3.28.32 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.99 Safety hangers. | FRA | Drive shafts shall have safety hangers. | |||||
| 49:49:4.1.1.1.23.3.28.33 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.101 Engines. | FRA | (a) The temperature and pressure alarms, controls and related switches of internal combustion engines shall function properly. (b) Whenever an engine has been shut down due to mechanical or other problems, a distinctive warning notice giving reason for the shut-down shall be conspicuously attached near the engine starting control until repairs have been made. (c) Wheel slip/slide protection shall be provided on a locomotive with an engine displaying a warning notice whenever required by § 229.115(b). | |||||
| 49:49:4.1.1.1.23.3.29.34 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.103 Safe working pressure; factor of safety. | FRA | The safe working pressure for each steam generator shall be fixed by the chief mechanical officer of the carrier. The minimum factor of safety shall be four. The fixed safe working pressure shall be indicated on FRA Form F 6180-49A. | |||||
| 49:49:4.1.1.1.23.3.29.35 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.105 Steam generator number. | FRA | An identification number shall be marked on the steam generator's separator and that number entered on FRA Form F 6180-49A. | |||||
| 49:49:4.1.1.1.23.3.29.36 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.107 Pressure gauge. | FRA | (a) Each steam generator shall have an illuminated steam gauge that correctly indicates the pressure. The steam pressure gauge shall be graduated to not less than one and one-half times the allowed working pressure of the steam generator. (b) Each steam pressure gauge on a steam generator shall have a siphon that prevents steam from entering the gauge. The pipe connection shall directly enter the separator and shall be steam tight between the separator and the gauge. | |||||
| 49:49:4.1.1.1.23.3.29.37 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.109 Safety valves. | FRA | Every steam generator shall be equipped with at least two safety valves that have a combined capacity to prevent an accumulation of pressure of more than five pounds per square inch above the allowed working pressure. The safety valves shall be independently connected to the separator and located as closely to the separator as possible without discharging inside of the generator compartment. The ends of the safety valve discharge lines shall be located or protected so that discharged steam does not create a hazard. | |||||
| 49:49:4.1.1.1.23.3.29.38 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.111 Water-flow indicator. | FRA | (a) Steam generators shall be equipped with an illuminated visual return water-flow indicator. (b) Steam generators shall be equipped with an operable test valve or other means of determining whether the steam generator is filled with water. The fill test valve may not discharge steam or hot water into the steam generator compartment. | |||||
| 49:49:4.1.1.1.23.3.29.39 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.113 Warning notice. | FRA | Whenever any steam generator has been shut down because of defects, a distinctive warning notice giving reasons for the shut-down shall be conspicuously attached near the steam generator starting controls until the necessary repairs have been made. The locomotive in which the steam generator displaying a warning notice is located may continue in service until the next periodic inspection. | |||||
| 49:49:4.1.1.1.23.3.29.40 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.114 Steam generator inspections and tests. | FRA | [77 FR 21346, Apr. 9, 2012] | (a) Periodic steam generator inspection. Except as provided in § 229.33, each steam generator shall be inspected and tested in accordance with paragraph (d) of this section at intervals not to exceed 92 days, unless the steam generator is isolated in accordance with paragraph (b) of this section. All non-complying conditions shall be repaired or the steam generator shall be isolated as prescribed in paragraph (b) of this section before the locomotive is used. (b) Isolation of a steam generator. A steam generator will be considered isolated if the water suction pipe to the water pump and the leads to the main switch (steam generator switch) are disconnected, and the train line shut-off-valve is wired closed or a blind gasket is applied. Before an isolated steam generator is returned to use, it shall be inspected and tested pursuant to paragraph (d) of this section. (c) Forms. Each periodic steam generator inspection and test shall be recorded on Form FRA F 6180-49A required by paragraph § 229.23. When Form FRA F 6180-49A for the locomotive is replaced, data for the steam generator inspections shall be transferred to the new Form FRA F6180-49A. (d) Tests and requirements. Each periodic steam generator inspection and test shall include the following tests and requirements: (1) All electrical devices and visible insulation shall be inspected. (2) All automatic controls, alarms, and protective devices shall be inspected and tested. (3) Steam pressure gauges shall be tested by comparison with a dead-weight tester or a test gauge designed for this purpose. The siphons to the steam gauges shall be removed and their connections examined to determine that they are open. (4) Safety valves shall be set and tested under steam after the steam pressure gauge is tested. (e) Annual steam generator tests. Each steam generator that is not isolated in accordance with paragraph (b) of this section, shall be subjected to a hydrostatic pressure at least 25 percent above the working pressure and the visual return water… | ||||
| 49:49:4.1.1.1.23.3.30.41 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.115 Slip/slide alarms. | FRA | (a) Except for MU locomotives, each locomotive used in road service shall be equipped with a device that provides an audible or visual alarm in the cab of either slipping or sliding wheels on powered axles under power. When two or more locomotives are coupled in multiple or remote control, the wheel slip/slide alarm of each locomotive shall be shown in the cab of the controlling locomotive. (b) Except as provided in § 229.9, an equipped locomotive may not be dispatched in road service, or continue in road service following a daily inspection, unless the wheel slip/slide protective device of whatever type— (1) Is functioning for each powered axle under power; and (2) Would function on each powered axle if it were under power. (c) Effective January 1, 1981, all new locomotives capable of being used in road service shall be equipped with a device that detects wheel slip/slide for each powered axle when it is under power. The device shall produce an audible or visual alarm in the cab. | |||||
| 49:49:4.1.1.1.23.3.30.42 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.117 Speed indicators. | FRA | (a) After December 31, 1980, each locomotive used as a controlling locomotive at speeds in excess of 20 miles per hour shall be equipped with a speed indicator which is— (1) Accurate within ±3 miles per hour of actual speed at speeds of 10 to 30 miles per hour and accurate within ±5 miles per hour at speeds above 30 miles per hour; and (2) Clearly readable from the engineer's normal position under all light conditions. (b) Each speed indicator required shall be tested as soon as possible after departure by means of speed test sections or equivalent procedures. | |||||
| 49:49:4.1.1.1.23.3.30.43 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.119 Cabs, floors, and passageways. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 77 FR 21346, Apr. 9, 2012] | (a) Cab seats shall be securely mounted and braced. Cab doors shall be equipped with a secure and operable latching device. (b) Cab windows of the lead locomotive shall provide an undistorted view of the right-of-way for the crew from their normal position in the cab. (See also, Safety Glazing Standards, 49 CFR part 223, 44 FR 77348, Dec. 31, 1979.) (c) Floors of cabs, passageways, and compartments shall be kept free from oil, water, waste or any obstruction that creates a slipping, tripping or fire hazard. Floors shall be properly treated to provide secure footing. (d) Any occupied locomotive cab shall be provided with proper ventilation and with a heating arrangement that maintains a temperature of at least 60 degrees Fahrenheit 6 inches above the center of each seat in the cab compartment. (e) Similar locomotives with open-end platforms coupled in multiple control and used in road service shall have a means of safe passage between them; no passageway is required through the nose of car body locomotives. There shall be a continuous barrier across the full width of the end of a locomotive or a continuous barrier between locomotives. (f) Containers shall be provided for carrying fusees and torpedoes. A single container may be used if it has a partition to separate fusees from torpedoes. Torpedoes shall be kept in a closed metal container. (g) Each locomotive or remanufactured locomotive placed in service for the first time on or after June 8, 2012, shall be equipped with an air conditioning unit in the locomotive cab compartment. (h) Each air conditioning unit in the locomotive cab on a locomotive identified in paragraph (g) of this section shall be inspected and maintained to ensure that it operates properly and meets or exceeds the manufacturer's minimum operating specifications during the periodic inspection required for the locomotive pursuant to § 229.23 of this part. (i) Each locomotive or remanufactured locomotive ordered on or after June 8, 2012, or placed in service for the first time on or after… | ||||
| 49:49:4.1.1.1.23.3.30.44 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.121 Locomotive cab noise. | FRA | [71 FR 63136, Oct. 27, 2006] | (a) Performance standards for locomotives. (1) When tested for static noise in accordance with paragraph (a)(3) of this section, all locomotives of each design or model that are manufactured after October 29, 2007, shall average less than or equal to 85 dB(A), with an upper 99% confidence limit of 87 dB(A). The railroad may rely on certification from the equipment manufacturer for a production run that this standard is met. The manufacturer may determine the average by testing a representative sample of locomotives or an initial series of locomotives, provided that there are suitable manufacturing quality controls and verification procedures in place to ensure product consistency. (2) In the maintenance of locomotives that are manufactured in accordance with paragraph (a)(1) of this section, a railroad shall not make any alterations that cause the average sound level for that locomotive design or model to exceed: (i) 82 dB(A) if the average sound level for a locomotive design or model is less than 82 dB(A); or (ii) 85 dB(A) if the average sound level for a locomotive design or model is 82 dB(A) to 85 dB(A), inclusive, (3) The railroad or manufacturer shall follow the static test protocols set forth in appendix H of this part to determine compliance with paragraph (a)(1) of this section; and, to the extent reasonably necessary to evaluate the effect of alterations during maintenance, to determine compliance with paragraph (a)(2) of this section. (b) Maintenance of locomotives. (1) If a railroad receives an excessive noise report, and if the condition giving rise to the noise is not required to be immediately corrected under part 229, the railroad shall maintain a record of the report, and repair or replace the item identified as substantially contributing to the noise: (i) On or before the next periodic inspection required by § 229.23; or (ii) If the railroad determines that the repair or replacement of the item requires significant shop or material resources that are not readily available, at the time … | ||||
| 49:49:4.1.1.1.23.3.30.45 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.123 Pilots, snowplows, end plates. | FRA | [77 FR 21347, Apr. 9, 2012] | (a) Each lead locomotive shall be equipped with a pilot, snowplow, or end plate that extends across both rails. The minimum clearance above the rail of the pilot, snowplow or end plate shall be 3 inches. Except as provided in paragraph (b) of this section, the maximum clearance shall be 6 inches. When the locomotive is equipped with a combination of the equipment listed in this paragraph, each extending across both rails, only the lowest piece of that equipment must satisfy clearance requirements of this section. (b) To provide clearance for passing over retarders, locomotives utilized in hump yard or switching service at hump yard locations may have pilot, snowplow, or end plate maximum height of 9 inches. (1) Each locomotive equipped with a pilot, snowplow, or end plate with clearance above 6 inches shall be prominently stenciled at each end of the locomotive with the words “9-inch Maximum End Plate Height, Yard or Trail Service Only.” (2) When operated in switching service in a leading position, locomotives with a pilot, snowplow, or end plate clearance above 6 inches shall be limited to 10 miles per hour over grade crossings. (3) Train crews shall be notified in writing of the restrictions on the locomotive, by label or stencil in the cab, or by written operating instruction given to the crew and maintained in the cab of the locomotive. (4) Pilot, snowplow, or end plate clearance above 6 inches shall be noted in the remarks section of Form FRA 6180-49a. (5) Locomotives with a pilot, snowplow, or end plate clearance above 6 inches shall not be placed in the lead position when being moved under section § 229.9. | ||||
| 49:49:4.1.1.1.23.3.30.46 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.125 Headlights and auxiliary lights. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 61 FR 8887, Mar. 6, 1996; 68 FR 49717, Aug. 19, 2003; 69 FR 12537, Mar. 16, 2004; 77 FR 21347, Apr. 9, 2012; 90 FR 28165, July 1, 2025] | (a) Each lead locomotive used in road service shall illuminate its headlight while the locomotive is in use. When illuminated, the headlight shall produce a peak intensity of at least 200,000 candela and produce at least 3,000 candela at an angle of 7.5 degrees and at least 400 candela at an angle of 20 degrees from the centerline of the locomotive when the light is aimed parallel to the tracks. If a locomotive or locomotive consist in road service is regularly required to run backward for any portion of its trip other than to pick up a detached portion of its train or to make terminal movements, it shall also have on its rear a headlight that meets the intensity requirements above. Each headlight shall be aimed to illuminate a person at least 800 feet ahead and in front of the headlight. For purposes of this section, a headlight shall be comprised of either one or two lamps. (1) If a locomotive is equipped with a single-lamp headlight, the single lamp shall produce a peak intensity of at least 200,000 candela and shall produce at least 3,000 candela at an angle of 7.5 degrees and at least 400 candela at an angle of 20 degrees from the centerline of the locomotive when the light is aimed parallel to the tracks. The following operative lamps meet the standard set forth in this paragraph: a single incandescent PAR-56, 200-watt, 30-volt lamp; a single halogen PAR-56, 200-watt, 30-volt lamp; a single halogen PAR-56, 350-watt, 75-volt lamp, or a single lamp meeting the intensity requirements given above. (2) If a locomotive is equipped with a dual-lamp headlight, a peak intensity of at least 200,000 candela and at least 3,000 candela at an angle of 7.5 degrees and at least 400 candela at an angle of 20 degrees from the centerline of the locomotive when the light is aimed parallel to the tracks shall be produced by the headlight based either on a single lamp capable of individually producing the required peak intensity or on the candela produced by the headlight with both lamps illuminated. If both lamps are needed t… | ||||
| 49:49:4.1.1.1.23.3.30.47 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.127 Cab lights. | FRA | (a) Each locomotive shall have cab lights which will provide sufficient illumination for the control instruments, meters, and gauges to enable the engine crew to make accurate readings from their normal positions in the cab. These lights shall be located, constructed, and maintained so that light shines only on those parts requiring illumination and does not interfere with the crew's vision of the track and signals. Each controlling locomotive shall also have a conveniently located light that can be readily turned on and off by the persons operating the locomotive and that provides sufficient illumination for them to read train orders and timetables. (b) Cab passageways and compartments shall have adequate illumination. | |||||
| 49:49:4.1.1.1.23.3.30.48 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.129 Locomotive horn. | FRA | [71 FR 47666, Aug. 17, 2006] | (a) Each lead locomotive shall be equipped with a locomotive horn that produces a minimum sound level of 96 dB(A) and a maximum sound level of 110 dB(A) at 100 feet forward of the locomotive in its direction of travel. The locomotive horn shall be arranged so that it can be conveniently operated from the engineer's usual position during operation of the locomotive. (b)(1) Each locomotive built on or after September 18, 2006 shall be tested in accordance with this section to ensure that the horn installed on such locomotive is in compliance with paragraph (a) of this section. Locomotives built on or after September 18, 2006 may, however, be tested in accordance with an acceptance sampling scheme such that there is a probability of .05 or less of rejecting a lot with a proportion of defectives equal to an AQL of 1% or less, as set forth in 7 CFR part 43. (2) Each locomotive built before September 18, 2006 shall be tested in accordance with this section before June 24, 2010 to ensure that the horn installed on such locomotive is in compliance with paragraph (a) of this section. (3) Each remanufactured locomotive, as determined pursuant to § 229.5 of this part, shall be tested in accordance with this section to ensure that the horn installed on such locomotive is in compliance with paragraph (a). (4)(i) Except as provided in paragraph (b)(4)(ii) of this section, each locomotive equipped with a replacement locomotive horn shall be tested, in accordance with paragraph (c) of this section, before the next two annual tests required by § 229.27 of this part are completed. (ii) Locomotives that have already been tested individually or through acceptance sampling, in accordance with paragraphs (b)(1), (b)(2), or (b)(3) of this section, shall not be required to undergo sound level testing when equipped with a replacement locomotive horn, provided the replacement locomotive horn is of the same model as the locomotive horn that was replaced and the mounting location and type of mounting are the same. (c) Testing of the l… | ||||
| 49:49:4.1.1.1.23.3.30.49 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.131 Sanders. | FRA | [72 FR 59223, Oct. 19, 2007] | (a) Prior to departure from an initial terminal, each locomotive, except for MU locomotives, shall be equipped with operative sanders that deposit sand on each rail in front of the first power operated wheel set in the direction of movement or shall be handled in accordance with the requirements contained in § 229.9. (b) A locomotive being used in road service with sanders that become inoperative after departure from an initial terminal shall be handled in accordance with the following: (1) A lead locomotive being used in road service that experiences inoperative sanders after departure from an initial terminal may continue in service until the earliest of the following occurrences: (i) Arrival at the next initial terminal; (ii) Arrival at a location where it is placed in a facility with a sand delivery system; (iii) The next periodic inspection under § 229.23; or (iv) Fourteen calendar days from the date the sanders are first discovered to be inoperative; and (2) A trailing locomotive being used in road service that experiences inoperative sanders after departure from an initial terminal may continue in service until the earliest of the following occurrence: (i) Arrival at the next initial terminal; (ii) Arrival at a location where it is placed in a facility with a sand delivery system; or (iii) The next periodic inspection under § 229.23. (c) A locomotive being used in switching service shall be equipped with operative sanders that deposit sand on each rail in front of the first power operated wheel set in the direction of movement. If the sanders become inoperative, the locomotive shall be handled in accordance with the following: (1) A locomotive being used in switching service at a location not equipped with a sand delivery system may continue in service for seven calendar days from the date the sanders are first discovered inoperative or until its next periodic inspection under § 229.23, which ever occurs first; and (2) A locomotive being used in switching service at locations equipped with a s… | ||||
| 49:49:4.1.1.1.23.3.30.50 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.133 Interim locomotive conspicuity measures—auxiliary external lights. | FRA | [58 FR 6902, Feb. 3, 1993, as amended at 59 FR 24963, May 13, 1994; 59 FR 39705, Aug. 4, 1994; 61 FR 8887, Mar. 6, 1996; 77 FR 21348, Apr. 9, 2012] | (a) A locomotive at the head of a train or other movement is authorized to be equipped with auxiliary external lights, additional to the headlight required by § 229.125, for the purpose of improved conspicuity. A locomotive that is equipped with auxiliary external lights in conformance with the specifications or performance standards set forth in paragraph (b) of this section on the date of issuance of a final rule that requires additional or other external lights on locomotives for improved conspicuity, as required by section 202(u) of the Federal Railroad Safety Act of 1970, shall be deemed to conform to the requirements of the final rule for four years following the date of issuance of that final rule. (b) Each qualifying arrangement of auxiliary external lights shall conform to one of the following descriptions: (1) Strobe lights. (i) Strobe lights shall consist of two white stroboscopic lights, each with “effective intensity,” as defined by the Illuminating Engineering Society's Guide for Calculating the Effective Intensity of Flashing Signal Lights (November 1964), of at least 500 candela. (ii) The flash rate of strobe lights shall be at least 40 flashes per minute and at most 180 flashes per minute. (iii) Strobe lights shall be placed at the front of the locomotive, at least 48 inches apart, and at least 36 inches above the top of the rail. (2) Oscillating light. (i) An oscillating light shall consist of: (A) One steadily burning white light producing at least 200,000 candela in a moving beam that depicts a circle or a horizontal figure “8” to the front, about the longitudinal centerline of the locomotive; or (B) Two or more white lights producing at least 200,000 candela each, at one location on the front of the locomotive, that flash alternately with beams within five degrees horizontally to either side of the longitudinal centerline of the locomotive. (ii) An oscillating light may incorporate a device that automatically extinguishes the white light if display of a light of another color is r… | ||||
| 49:49:4.1.1.1.23.3.30.51 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.135 Event recorders. | FRA | [70 FR 37940, June 30, 2005, as amended at 75 FR 2697, Jan. 15, 2010] | (a) Duty to equip and record. Except as provided in paragraphs (c) and (d) of this section, a train operated faster than 30 miles per hour shall have an in-service event recorder, of the type described in paragraph (b) of this section, in the lead locomotive. The presence of the event recorder shall be noted on Form FRA F6180-49A (by writing the make and model of event recorder with which the locomotive is equipped) under the REMARKS section, except that an event recorder designed to allow the locomotive to assume the lead position only if the recorder is properly functioning is not required to have its presence noted on Form FRA F6180-49A. For the purpose of this section, “train” includes a locomotive or group of locomotives with or without cars. The duty to equip the lead locomotive may be met with an event recorder located elsewhere than the lead locomotive provided that such event recorder monitors and records the required data as though it were located in the lead locomotive. The event recorder shall record the most recent 48 hours of operation of the electrical system of the locomotive on which it is installed. (b) Equipment requirements. Event recorders shall monitor and record data elements required by this paragraph with at least the accuracy required of the indicators displaying any of the required elements to the engineer. (1) A lead locomotive originally ordered before October 1, 2006, and placed in service before October 1, 2009, including a controlling remote distributed power locomotive, a lead manned helper locomotive, a DMU locomotive, and an MU locomotive, except as provided in paragraphs (c) and (d) of this section, shall have an in-service event recorder that records the following data elements: (i) Train speed; (ii) Selected direction of motion; (iii) Time; (iv) Distance; (v) Throttle position; (vi) Applications and operations of the train automatic air brake; (vii) Applications and operations of the independent brake; (viii) Applications and operations of the dynamic brake, if … | ||||
| 49:49:4.1.1.1.23.3.30.52 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.136 Locomotive image and audio recording devices. | FRA | [88 FR 70761, Oct. 12, 2023] | (a) Duty to equip and record. (1) Effective October 12, 2027, each lead locomotive of a train used in commuter or intercity passenger service must be equipped with an image recording system to record images of activities ahead of the locomotive in the direction of travel (outward-facing image recording device), and of activities inside the cab of the locomotive (inward-facing image recording device). (i) If the lead locomotive is equipped with an image recording system, the system must be turned on and recording whenever a train is in motion, at all train speeds. (ii) If operating circumstances cause the controlling locomotive to be other than the lead locomotive, railroads must also record images of activities inside the cab of the controlling locomotive. (iii) Both cabs of a dual-cab locomotive shall be equipped with inward- and outward-facing image recording systems. Image recordings for only a dual-cab locomotive's active cab and the leading end of the locomotive's movement are required to be made and retained. (2) Image recording systems installed after October 12, 2024, on new, remanufactured, or existing lead locomotives used in commuter or intercity passenger service shall meet the requirements of this section. Lead locomotives used in commuter or intercity passenger service must be equipped with an image recording system meeting the requirements of this section no later than October 12, 2027. (3) For lead locomotives in commuter or intercity passenger service, railroads must note the presence of any image or audio recording systems in the REMARKS section of Form FRA F 6180-49AP in the locomotive cab. (4) As required under paragraph (a)(1) or (2) of this section, the image recording system shall record at least the most recent 12 hours of operation of a lead locomotive in commuter or intercity passenger service. (5) Locomotive recording device data for each lead locomotive used in commuter or intercity passenger service shall be recorded on a memory module meeting the requirements for a certified… | ||||
| 49:49:4.1.1.1.23.3.30.53 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.137 Sanitation, general requirements. | FRA | [67 FR 16050, Apr. 4, 2002, as amended at 71 FR 61857, Oct. 19, 2006] | (a) Sanitation compartment. Except as provided in paragraph (b) of this section, all lead locomotives in use shall be equipped with a sanitation compartment. Each sanitation compartment shall be: (1) Adequately ventilated; (2) Equipped with a door that: (i) Closes, and (ii) Possesses a modesty lock by [18 months after publication of the final rule]; (3) Equipped with a toilet facility, as defined in this part; (4) Equipped with a washing system, as defined in this part, unless the railroad otherwise provides the washing system to employees upon reporting for duty or occupying the cab for duty, or where the locomotive is equipped with a stationary sink that is located outside of the sanitation compartment; (5) Equipped with toilet paper in sufficient quantity to meet employee needs, unless the railroad otherwise provides toilet paper to employees upon reporting for duty or occupying the cab for duty; and (6) Equipped with a trash receptacle, unless the railroad otherwise provides portable trash receptacles to employees upon reporting for duty or occupying the cab for duty. (b) Exceptions. (1) Paragraph (a) of this section shall not apply to: (i) Locomotives engaged in commuter service or other short-haul passenger service and commuter work trains on which employees have ready access to railroad-provided sanitation facilities outside of the locomotive or elsewhere on the train, that meet otherwise applicable sanitation standards, at frequent intervals during the course of their work shift; (ii) Locomotives engaged in switching service on which employees have ready access to railroad-provided sanitation facilities outside of the locomotive, that meet otherwise applicable sanitation standards, at frequent intervals during the course of their work shift; (iii) Locomotives engaged in transfer service on which employees have ready access to railroad-provided sanitation facilities outside of the locomotive, that meet otherwise applicable sanitation standards, at frequent intervals during the course of the… | ||||
| 49:49:4.1.1.1.23.3.30.54 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.139 Sanitation, servicing requirements. | FRA | [67 FR 16050, Apr. 4, 2002] | (a) The sanitation compartment of each lead locomotive in use shall be sanitary. (b) All components required by § 229.137(a) for the lead locomotive in use shall be present consistent with the requirements of this part, and shall operate as intended such that: (1) All mechanical systems shall function; (2) Water shall be present in sufficient quantity to permit flushing; (3) For those systems that utilize chemicals for treatment, the chemical (chlorine or other comparable oxidizing agent) used to treat waste must be present; and (4) No blockage is present that prevents waste from evacuating the bowl. (c) The sanitation compartment of each occupied locomotive used in switching service pursuant to § 229.137(b)(1)(ii), in transfer service pursuant to § 229.137(b)(1)(iii), or in a trailing position when the locomotive is occupied, shall be sanitary. (d) Where the railroad uses a locomotive pursuant to § 229.137(e) in switching or transfer service with a defective toilet facility, such use shall not exceed 10 calendar days from the date on which the defective toilet facility became defective. The date on which the toilet facility becomes defective shall be entered on the daily inspection report. (e) Where it is determined that the modesty lock required by § 229.137(a)(2) is defective, the railroad shall repair the modesty lock on or before the next 92-day inspection required by this part. | ||||
| 49:49:4.1.1.1.23.3.30.55 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.140 Alerters. | FRA | [77 FR 21348, Apr. 9, 2012, as amended at 77 FR 75057, Dec. 19, 2012] | (a) Except for locomotives covered by part 238 of this chapter, each of the following locomotives shall be equipped with a functioning alerter as described in paragraphs (b) through (d) of this section: (1) A locomotive that is placed in service for the first time on or after June 10, 2013, when used as a controlling locomotive and operated at speeds in excess of 25 mph. (2) All controlling locomotives operated at speeds in excess of 25 mph on or after January 1, 2017. (b) The alerter on locomotives subject to paragraph (a) of this section shall be equipped with a manual reset and the alerter warning timing cycle shall automatically reset as the result of any of the following operations, and at least three of the following automatic resets shall be functional at any given time: (1) Movement of the throttle handle; (2) Movement of the dynamic brake control handle; (3) Movement of the operator's horn activation handle; (4) Movement of the operator's bell activation switch; (5) Movement of the automatic brake valve handle; or (6) Bailing the independent brake by depressing the independent brake valve handle. (c) All alerters shall provide an audio alarm upon expiration of the timing cycle interval. An alerter on a locomotive that is placed in service for the first time on or after June 10, 2013, shall display a visual indication to the operator at least five seconds prior to an audio alarm. The visual indication on an alerter so equipped shall be visible to the operator from their normal position in the cab. (d) Alerter warning timing cycle interval shall be within 10 seconds of the calculated setting utilizing the formula (timing cycle specified in seconds = 2400 ÷ track speed specified in miles per hour). For locomotives operating at speeds below 20 mph, the interval shall be between 110 seconds and 130 seconds. (e) Any locomotive that is equipped with an alerter shall have the alerter functioning and operating as intended when the locomotive is used as a controlling locomotive. (f) A controlling loco… | ||||
| 49:49:4.1.1.1.23.3.30.56 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | C | Subpart C—Safety Requirements | § 229.141 Body structure, MU locomotives. | FRA | [45 FR 21109, Mar. 31, 1980, as amended at 71 FR 36912, June 28, 2006] | (a) MU locomotives built new after April 1, 1956 that are operated in trains having a total empty weight of 600,000 pounds or more shall have a body structure designed to meet or exceed the following minimum specifications: (1) The body structure shall resist a minimum static end load of 800,000 pounds at the rear draft stops ahead of the bolster on the center line of draft, without developing any permanent deformation in any member of the body structure. (2) An anti-climbing arrangement shall be applied at each end that is designed so that coupled MU locomotives under full compression shall mate in a manner that will resist one locomotive from climbing the other. This arrangement shall resist a vertical load of 100,000 pounds without exceeding the yield point of its various parts or its attachments to the body structure. (3) The coupler carrier and its connections to the body structure shall be designed to resist a vertical downward thrust from the coupler shank of 100,000 pounds for any horizontal position of the coupler, without exceeding the yield points of the materials used. When yielding type of coupler carrier is used, an auxiliary arrangement shall be provided that complies with these requirements. (4) The outside end of each locomotive shall be provided with two main vertical members, one at each side of the diaphragm opening; each main member shall have an ultimate shear value of not less than 300,000 pounds at a point even with the top of the underframe member to which it is attached. The attachment of these members at bottom shall be sufficient to develop their full shear value. If reinforcement is used to provide the shear value, the reinforcement shall have full value for a distance of 18 inches up from the underframe connection and then taper to a point approximately 30 inches above the underframe connection. (5) The strength of the means of locking the truck to the body shall be at least the equivalent of an ultimate shear value of 250,000 pounds. (6) On or after November 8, 1999, paragraph… | ||||
| 49:49:4.1.1.1.23.4.31.1 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.201 Purpose and scope. | FRA | [71 FR 36912, June 28, 2006] | (a) Purpose. The purpose of this subpart is to help protect locomotive cab occupants in the event that a locomotive collides with another locomotive or piece of on-track equipment, a shifted load on a freight car on an adjacent parallel track, or a highway vehicle at a highway-rail grade crossing. (b) This subpart prescribes minimum crashworthiness standards for locomotives. It also establishes the requirements for obtaining FRA approval of: new locomotive crashworthiness design standards; changes to FRA-approved locomotive crashworthiness design standards; and alternative locomotive crashworthiness designs. | ||||
| 49:49:4.1.1.1.23.4.31.10 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.217 Fuel tank. | FRA | [71 FR 36914, June 28, 2006, as amended at 74 FR 25173, May 27, 2009] | (a) External fuel tanks. Locomotives equipped with external fuel tanks shall, at a minimum, comply with the requirements of AAR S-5506, “Performance Requirements for Diesel Electric Locomotive Fuel Tanks” (October 1, 2001), except for section 4.4. This paragraph does not apply to locomotives subject to the fuel tank safety requirements of § 238.223 or § 238.423 of this chapter. The Director of the Federal Register approves incorporation by reference of the AAR S-5506, “Performance Requirements for Diesel Electric Locomotive Fuel Tanks” (October 1, 2001) in this section in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. You may obtain a copy of the incorporated standard from the Association of American Railroads, 50 F Street NW., Washington, DC 20001. You may inspect a copy of the incorporated standard at the Federal Railroad Administration, Docket Clerk, 1200 New Jersey Avenue, SE., Washington, DC 20590 or at the National Archives and Records Administration (NARA). For more information on the availability of this material at NARA, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (b) Internal fuel tanks. Locomotives equipped with internal fuel tanks shall, at a minimum, comply with the requirements of § 238.223(b) of this chapter. | ||||
| 49:49:4.1.1.1.23.4.31.2 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.203 Applicability. | FRA | [71 FR 36912, June 28, 2006] | (a) Except as provided in paragraphs (b) and (c) of this section, this subpart applies to all locomotives manufactured or remanufactured on or after January 1, 2009. (b) Cab cars and power cars. The requirements of this subpart do not apply to cab control cars, MU locomotives, DMU locomotives, and semi-permanently coupled power cars that are subject to the design requirements for such locomotives set forth in part 238 of this chapter. (c) Locomotives used in designated service. Locomotives used in designated service are exempt from the requirements of this subpart, with the exception of § 229.233 (minimum requirements for fuel tank design), which remains applicable to such locomotives. | ||||
| 49:49:4.1.1.1.23.4.31.3 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.205 General requirements. | FRA | [71 FR 36912, June 28, 2006, as amended at 74 FR 25173, May 27, 2009] | (a) Each wide-nose locomotive used in occupied service must meet the minimum crashworthiness performance requirements set forth in Appendix E of this part. Compliance with those performance criteria must be established by: (1) Meeting an FRA-approved crashworthiness design standard (including AAR S-580, Locomotive Crashworthiness Requirements). The Director of the Federal Register approves incorporation by reference of the AAR S-580 (revised July 2005), “Locomotive Crashworthiness Requirements,” in this section in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. You may obtain a copy of the incorporated standard from the Association of American Railroads, 50 F Street NW, Washington, DC 20001. You may inspect a copy of the incorporated standard at the Federal Railroad Administration, Docket Clerk, 1200 New Jersey Avenue, SE., Washington, DC 20590 or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html; (2) Meeting new design standards and changes to existing design standards approved by FRA pursuant to § 229.207; or (3) Meeting an alternative crashworthiness design approved by FRA pursuant to § 229.209. (b) A monocoque or semi-monocoque design locomotive must be designed in accordance with the provisions of AAR S-580, applicable to those types of locomotives, in accordance with §§ 238.405(a), 238.409 and 238.411 of this chapter, or in accordance with a standard or design approved by FRA as providing at least equivalent safety. (c) A narrow-nose locomotive must be designed in accordance with the provisions of AAR S-580, applicable to that type of locomotive (notwithstanding any limitation of scope contained in that standard) or in accordance with a standard or design approved by FRA as providing at least equivalent safety. | ||||
| 49:49:4.1.1.1.23.4.31.4 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.206 Design requirements. | FRA | [71 FR 36912, June 28, 2006] | Each locomotive used in occupied service must meet the minimum anti-climber, emergency egress, emergency interior lighting, and interior configuration design requirements set forth in AAR S-580 (incorporated by reference, see § 229.205). | ||||
| 49:49:4.1.1.1.23.4.31.5 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.207 New locomotive crashworthiness design standards and changes to existing FRA-approved locomotive crashworthiness design standards. | FRA | [71 FR 36912, June 28, 2006, as amended at 74 FR 25173, May 27, 2009] | (a) General. The following procedures govern consideration and action upon requests for FRA approval of new locomotive crashworthiness design standards and changes to existing FRA-approved locomotive crashworthiness design standards, including AAR S-580 (incorporated by reference, see § 229.205). Only a standards body which has adopted an FRA-approved locomotive crashworthiness design standard may initiate these procedures for FRA approval of changes to the standard. (b) Petitions for FRA approval of new locomotive crashworthiness design standards. Each petition for FRA approval of a locomotive crashworthiness design standard must be titled “Petition for FRA Approval of a New Locomotive Crashworthiness Design Standard,” must be submitted to the Associate Administrator for Safety, Federal Railroad Administration, 1200 New Jersey Avenue, SE., Mail Stop 25, Washington, DC 20590, and must contain the following: (1) The name, title, address, telephone number and e-mail address of the primary person to be contacted with regard to review of the petition; (2) The proposed locomotive design standard, in detail; (3) The intended type of service for locomotives designed under the proposed standard; and (4) Appropriate data and analysis showing how the proposed design standard either satisfies the requirements of § 229.205 for the type of locomotive design or provides at least an equivalent level of safety. Types of data and analysis to be considered are described in § 229.211(c)(1). (c) Petitions for FRA approval of substantive changes to an FRA-approved locomotive crashworthiness design standard. Each petition for approval of a substantive change to an FRA-approved locomotive crashworthiness design standard must be titled “Petition for FRA Approval of Changes to a Locomotive Crashworthiness Design Standard,” must be submitted to the Associate Administrator for Safety, Federal Railroad Administration, 1200 New Jersey Avenue, SE., Mail Stop 25, Washington, DC 20590, and must contain the following: (1) The name, … | ||||
| 49:49:4.1.1.1.23.4.31.6 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.209 Alternative locomotive crashworthiness designs. | FRA | [71 FR 36913, June 28, 2006, as amended at 74 FR 25173, May 27, 2009] | (a) General. The following procedures govern consideration and action upon requests for FRA approval of locomotive crashworthiness designs which are not consistent with any FRA-approved locomotive crashworthiness design standard. (b) Petitions for FRA approval of alternative locomotive crashworthiness designs. Each petition for FRA approval of an alternative locomotive crashworthiness design must be titled “Petition for FRA Approval of Alternative Locomotive Crashworthiness Design,” must be submitted to the Associate Administrator for Safety, Federal Railroad Administration, 1200 New Jersey Avenue, SE., Mail Stop 25, Washington, DC 20590, and must contain the following: (1) The name, title, address, telephone number and e-mail address of the primary person to be contacted with regard to review of the petition; (2) The proposed locomotive crashworthiness design, in detail; (3) The intended type of service for locomotives built under the proposed design; and (4) Appropriate data and analysis showing how the design either satisfies the requirements of § 229.205 for the type of locomotive or provides at least an equivalent level of safety. Types of data and analysis to be considered are described in § 229.211(c)(1). | ||||
| 49:49:4.1.1.1.23.4.31.7 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.211 Processing of petitions. | FRA | [71 FR 36913, June 28, 2006, as amended at 74 FR 25173, May 27, 2009] | (a) Federal Register notice. FRA will publish in the Federal Register notice of receipt of each petition submitted under § 229.207(b), § 229.207(c), or § 229.209. (b) Comment. Not later than 60 days from the date of publication of the notice in the Federal Register concerning a petition submitted under §§ 229.207(b), 229.207(c), or 229.209(b), any person may comment on the petition. (1) Each comment must set forth specifically the basis upon which it is made, and contain a concise statement of the interest of the commenter in the proceeding. (2) Each comment must be submitted to the U.S. Department of Transportation Docket Operations (M-30), West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, and must contain the assigned docket number which appeared in the Federal Register for that proceeding. The form of such submission may be in written or electronic form consistent with the standards and requirements established by the Federal Docket Management System and posted on its Web site at http://www.regulations.gov. (3) In the event FRA requires additional information to appropriately consider the petition, FRA will conduct a hearing on the petition in accordance with the procedures provided in § 211.25 of this chapter. (c) Disposition of petitions. (1) In order to determine compliance with the performance criteria in appendix E of this part, FRA will consider proper documentation of competent engineering analysis, or practical demonstrations, or both which may include validated computer modeling, structural crush analysis, component testing, full scale crash testing in a controlled environment, or any combination of the foregoing, together with evidence of effective peer review. (2) If FRA finds that the petition complies with the requirements of this subpart and that the proposed change or new design standard satisfies the requirements of § 229.205 for the type of locomotive, the petition will be granted, normally within 90 days of its receipt. If the peti… | ||||
| 49:49:4.1.1.1.23.4.31.8 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.213 Locomotive manufacturing information. | FRA | [71 FR 36914, June 28, 2006] | (a) Each railroad operating a locomotive subject to the requirements of this subpart must retain the following information: (1) The date upon which the locomotive was manufactured or remanufactured; (2) The name of the manufacturer or remanufacturer of the locomotive; and (3) The design specification to which the locomotive was manufactured or remanufactured. (b) The information required in paragraph (a) of this section must be located permanently in the locomotive cab or be provided within two business days upon request of FRA or an FRA-certified State inspector. | ||||
| 49:49:4.1.1.1.23.4.31.9 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | D | Subpart D—Locomotive Crashworthiness Design Requirements | § 229.215 Retention and inspection of designs. | FRA | [71 FR 36914, June 28, 2006] | (a) Retention of records—original designs. Each manufacturer or remanufacturer of a locomotive subject to this subpart shall retain all records of the original locomotive designs, including supporting calculations and drawings, pertaining to crashworthiness features required by this subpart. These records must be retained for the lesser period of: (1) The life of such locomotive, except that records for a locomotive destroyed in a rail equipment accident/incident shall be retained for at least 12 months following the accident/incident; or (2) Twenty years after the date of manufacture or, if remanufactured, twenty years after the date of remanufacture. (b) Retention of records—repairs and modifications. Each owner or lessee of a locomotive subject to this subpart shall retain all records of repair or modification to crashworthiness features required by this subpart. These records must be retained for the lesser period of: (1) The life of such locomotive, except that records for a locomotive destroyed in a rail equipment accident/incident shall be retained for at least 12 months following the accident/incident, or (2) Twenty years after the date on which the repair or modification was performed. (c) Inspection of records. Each custodian of records referred to in paragraphs (a) and (b) shall, upon request by FRA or an FRA-certified State inspector, make available for inspection and duplication within 7 days, any records referred to in paragraphs (a) and (b) of this section. (d) Third party storage of records. Each custodian of records referred to in paragraphs (a) and (b) of this section may delegate storage duties to a third party; however, the custodian retains all responsibility for compliance with this section. | ||||
| 49:49:4.1.1.1.23.5.31.1 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.301 Purpose and scope. | FRA | (a) The purpose of this subpart is to promote the safe design, operation, and maintenance of safety-critical, as defined in § 229.305, electronic locomotive control systems, subsystems, and components. (b) Locomotive control systems or their functions that comingle with safety critical processor based signal and train control systems are regulated under part 236 subparts H and I of this chapter. | |||||
| 49:49:4.1.1.1.23.5.31.10 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.319 Operating Personnel Training. | FRA | (a) The training required under § 229.317 for any locomotive engineer or other person who participates in the operation of a train using an onboard electronic locomotive control system shall address all of the following elements and shall be specified in the training program. (1) Familiarization with the electronic control system equipment onboard the locomotive and the functioning of that equipment as part of the system and in relation to other onboard systems under that person's control; (2) Any actions required of the operating personnel to enable or enter data into the system and the role of that function in the safe operation of the train; (3) Sequencing of interventions by the system, including notification, enforcement, penalty initiation and post penalty application procedures as applicable; (4) Railroad operating rules applicable to control systems, including provisions for movement and protection of any unequipped trains, or trains with failed or cut-out controls; (5) Means to detect deviations from proper functioning of onboard electronic control system equipment and instructions explaining the proper response to be taken regarding control of the train and notification of designated railroad personnel; and (6) Information needed to prevent unintentional interference with the proper functioning of onboard electronic control equipment. (b) The training required under this subpart for a locomotive engineer and conductor, together with required records, shall be integrated into the program of training required by parts 240 and 242 of this chapter. | |||||
| 49:49:4.1.1.1.23.5.31.2 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.303 Applicability. | FRA | [77 FR 21348, Apr. 9, 2012, as amended at 77 FR 75057, Dec. 19, 2012] | (a) The requirements of this subpart apply to all safety-critical electronic locomotive control systems, subsystems, and components (i.e., “products” as defined in § 229.305), except for the following: (1) Products that are fully developed prior to June 8, 2012. (2) Products that are under development as of October 9, 2012, and are fully developed prior to October 9, 2017. (3) Products that comingle locomotive control systems with safety critical processor based signal and train control systems; (4) Products that are used during on-track testing within a test facility; and (5) Products that are used during on-track testing outside a test facility, if approved by FRA. To obtain FRA approval of on-track testing outside of a test facility, a railroad shall submit a request to FRA that provides: (i) Adequate information regarding the function and history of the product that it intends to use; (ii) The proposed tests; (iii) The date, time and location of the tests; and (iv) The potential safety consequences that will result from operating the product for purposes of testing. (b) Railroads and vendors shall identify all products identified in paragraph (a)(2) of this section to FRA by February 9, 2013. (c) The exceptions provided in paragraph (a) of this section do not apply to products or product changes that result in degradation of safety, or a material increase in safety-critical functionality. | ||||
| 49:49:4.1.1.1.23.5.31.3 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.305 Definitions. | FRA | [77 FR 21348, Apr. 9, 2012, as amended at 77 FR 75057, Dec. 19, 2012] | As used in this subpart— Cohesion is a measure of how strongly-related or focused the responsibilities of a system, subsystem, or component are. Comingle refers to the act of creating systems, subsystems, or components where the systems, subsystems, or components are tightly coupled and with low cohesion. Component means an electronic element, device, or appliance (including hardware or software) that is part of a system or subsystem. Configuration management control plan means a plan designed to ensure that the proper and intended product configuration, including the electronic hardware components and software version, is documented and maintained through the life-cycle of the products in use. Executive software means software common to all installations of a given electronic product. It generally is used to schedule the execution of the site-specific application programs, run timers, read inputs, drive outputs, perform self-diagnostics, access and check memory, and monitor the execution of the application software to detect unsolicited changes in outputs. Initialization refers to the startup process when it is determined that a product has all required data input and the product is prepared to function as intended. Loosely coupled means an attribute of systems, referring to an approach to designing interfaces across systems, subsystems, or components to reduce the interdependencies between them—in particular, reducing the risk that changes within one system, subsystem, or component will create unanticipated changes within other system, subsystem, or component. Materials handling refers to explicit instructions for handling safety-critical components established to comply with procedures specified by the railroad. Product means any safety critical electronic locomotive control system, subsystem, or component, not including safety critical processor based signal and train control systems, whose functions are directly related to safe movement and stopping of the train as well as the associated ma… | ||||
| 49:49:4.1.1.1.23.5.31.4 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.307 Safety analysis. | FRA | (a) A railroad shall develop a Safety Analysis (SA) for each product subject to this subpart prior to the initial use of such product on their railroad. (b) The SA shall: (1) establish and document the minimum requirements that will govern the development and implementation of all products subject to this subpart, and be based on good engineering practice and should be consistent with the guidance contained in appendix F of this part in order to establish that a product's safety-critical functions will operate with a high degree of confidence in a fail-safe manner; (2) Include procedures for immediate repair of safety-critical functions; and (3) Be made available to FRA upon request. (c) Each railroad shall comply with the SA requirements and procedures related to the development, implementation, and repair of a product subject to this subpart. | |||||
| 49:49:4.1.1.1.23.5.31.5 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.309 Safety-critical changes and failures. | FRA | (a) Whenever a planned safety-critical design change is made to a product that is in use by a railroad and subject to this subpart, the railroad shall: (1) Notify FRA's Associate Administrator for Safety of the design changes made by the product supplier; (2) Ensure that the SA is updated as required; (3) Conduct all safety-critical changes in a manner that allows the change to be audited; (4) Specify all contractual arrangements with suppliers and private equipment owners for notification of any and all electronic safety-critical changes as well as safety-critical failures in the suppliers and private equipment owners' system, subsystem, or components, and the reasons for that change or failure from the suppliers or equipment owners, whether or not the railroad has experienced a failure of that safety critical system, sub-system, or component; (5) Specify the railroad's procedures for action upon receipt of notification of a safety-critical change or failure of an electronic system, sub-system, or component, and until the upgrade or revision has been installed; and (6) Identify all configuration/revision control measures designed to ensure that safety-functional requirements and safety-critical hazard mitigation processes are not compromised as a result of any such change, and that any such change can be audited. (b) Product suppliers and private equipment owners shall report any safety-critical changes and previously unidentified hazards to each railroad using the product or equipment. (c) Private equipment owners shall establish configuration/revision control measures for control of safety-critical changes and identification of previously unidentified hazards. | |||||
| 49:49:4.1.1.1.23.5.31.6 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.311 Review of SAs. | FRA | (a) Prior to the initial planned use of a product subject to this subpart, a railroad shall inform the Associate Administrator for Safety/Chief Safety Officer, FRA, 1200 New Jersey Avenue SE., Mail Stop 25, Washington, DC 20590 of the intent to place this product in service. The notification shall provide a description of the product, and identify the location where the complete SA documentation described in § 229.307, the testing records contained in § 229.313, and the training and qualification program described in § 229.319 is maintained. (b) FRA may review or audit the SA within 60 days of receipt of the notification or anytime after the product is placed in use. If FRA has not notified the railroad of its intent to review or audit the SA within the 60-day period, the railroad may assume that FRA does not intend to review or audit, and place the product in use. FRA reserves the right, however, to conduct a review or audit at a later date. (c) A railroad shall maintain and make available to FRA upon request all railroad or vendor documentation used to demonstrate that the product meets the safety requirements of the SA for the life-cycle of the product. (d) After a product is placed in service, the railroad shall maintain a database of all safety-relevant hazards encountered with the product. The database shall include all hazards identified in the SA and those that had not been previously identified in the SA. If the frequency of the safety-relevant hazards exceeds the threshold set forth in the SA, then the railroad shall: (1) Report the inconsistency by mail, facsimile, email, or hand delivery to the Director, Office of Safety Assurance and Compliance, FRA, 1200 New Jersey Ave. SE., Mail Stop 25, Washington, DC 20590, within 15 days of discovery; (2) Take immediate countermeasures to reduce the frequency of the safety-relevant hazard(s) below the threshold set forth in the SA; and (3) Provide a final report to FRA's Director, Office of Safety Assurance and Compliance, on the results of the analysis an… | |||||
| 49:49:4.1.1.1.23.5.31.7 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.313 Product testing results and records. | FRA | (a) Results of product testing conducted by a railroad as required by this subpart shall be recorded on preprinted forms provided by the railroad, or stored electronically. Electronic recordkeeping or automated tracking systems, subject to the provisions contained in paragraph (e) of this section, may be utilized to store and maintain any testing or training record required by this subpart. Results of product testing conducted by a vendor or private equipment owner in support of a SA shall be provided to the railroad as part of the SA. (b) The testing records shall contain all of the following: (1) The name of the railroad; (2) The location and date that the test was conducted; (3) The equipment tested; (4) The results of tests; (5) The repairs or replacement of equipment; (6) Any preventative adjustments made; and (7) The condition in which the equipment is left. (c) Each record shall be: (1) Signed by the employee conducting the test, or electronically coded, or identified by the automated test equipment number; (2) Filed in the office of a supervisory official having jurisdiction, unless otherwise noted; and (3) Available for inspection and copying by FRA. (d) The results of the testing conducted in accordance with this subpart shall be retained as follows: (1) The results of tests that pertain to installation or modification of a product shall be retained for the life-cycle of the product tested and may be kept in any office designated by the railroad; (2) The results of periodic tests required for the maintenance or repair of the product tested shall be retained until the next record is filed and in no case less than one year; and (3) The results of all other tests and training shall be retained until the next record is filed and in no case less than one year. (e) Electronic or automated tracking systems used to meet the requirements contained in paragraph (a) of this section shall be capable of being reviewed and monitored by FRA at any time to ensure the integrity of the system. FRA's Asso… | |||||
| 49:49:4.1.1.1.23.5.31.8 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.315 Operations and maintenance manual. | FRA | (a) The railroad shall maintain all documents pertaining to the installation, maintenance, repair, modification, inspection, and testing of a product subject to this part in one Operations and Maintenance Manual (OMM). (1) The OMM shall be legible and shall be readily available to persons who conduct the installation, maintenance, repair, modification, inspection, and testing, and for inspection by FRA. (2) At a minimum, the OMM shall contain all product vendor operation and maintenance guidance. (b) The OMM shall contain the plans and detailed information necessary for the proper maintenance, repair, inspection, and testing of products subject to this subpart. The plans shall identify all software versions, revisions, and revision dates. (c) Hardware, software, and firmware revisions shall be documented in the OMM according to the railroad's configuration management control plan. (d) Safety-critical components, including spare products, shall be positively identified, handled, replaced, and repaired in accordance with the procedures specified in the railroad's configuration management control plan. (e) A railroad shall determine that the requirements of this section have been met prior to placing a product subject to this subpart in use on their property. | |||||
| 49:49:4.1.1.1.23.5.31.9 | 49 | Transportation | II | 229 | PART 229—RAILROAD LOCOMOTIVE SAFETY STANDARDS | E | Subpart E—Locomotive Electronics | § 229.317 Training and qualification program. | FRA | (a) A railroad shall establish and implement training and qualification program for products subject to this subpart prior to the product being placed in use. These programs shall meet the requirements set forth in this section and in § 229.319. (b) The program shall provide training for the individuals identified in this paragraph to ensure that they possess the necessary knowledge and skills to effectively complete their duties related to the product. These include: (1) Individuals whose duties include installing, maintaining, repairing, modifying, inspecting, and testing safety-critical elements of the product; (2) Individuals who operate trains or serve as a train or engine crew member subject to instruction and testing under part 217 of this chapter; (3) Roadway and maintenance-of-way workers whose duties require them to know and understand how the product affects their safety and how to avoid interfering with its proper functioning; and (4) Direct supervisors of the individuals identified in paragraphs (b)(1) through (3) of this section. (c) When developing the training and qualification program required in this section, a railroad shall conduct a formal task analysis. The task analysis shall: (1) Identify the specific goals of the program for each target population (craft, experience level, scope of work, etc.), task(s), and desired success rate; (2) Identify the installation, maintenance, repair, modification, inspection, testing, and operating tasks that will be performed on the railroad's products, including but not limited to the development of failure scenarios and the actions expected under such scenarios; (3) Develop written procedures for the performance of the tasks identified; and (4) Identify any additional knowledge, skills, and abilities above those required for basic job performance necessary to perform each task. (d) Based on the task analysis, a railroad shall develop a training curriculum that includes formally structured training designed to impart the knowledge, skills, and ab… |
Advanced export
JSON shape: default, array, newline-delimited, object
CREATE TABLE cfr_sections (
section_id TEXT PRIMARY KEY,
title_number INTEGER,
title_name TEXT,
chapter TEXT,
subchapter TEXT,
part_number TEXT,
part_name TEXT,
subpart TEXT,
subpart_name TEXT,
section_number TEXT,
section_heading TEXT,
agency TEXT,
authority TEXT,
source_citation TEXT,
amendment_citations TEXT,
full_text TEXT
);
CREATE INDEX idx_cfr_title ON cfr_sections(title_number);
CREATE INDEX idx_cfr_part ON cfr_sections(part_number);
CREATE INDEX idx_cfr_agency ON cfr_sections(agency);